10648267891 Kenmore Refrigerator - Instructions

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.

Per instructions

I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

The repair was simple. Unplug the refrigerator, unplug the power connector from the fan and remove 3 screws. I removed the fan blade clip with the pliers and cleaned it off. Reversed the process, cleaned all the dust out with my shop vac and all works perfectly now. It took longer to pull the fridge out of it's normal position than to perform the repair. Every day it continues to work is one more day I don't spend $2000 or more on a replacement.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.

Removed refrig. door and replaced closing cam and tightened the bottom cam