10648067892 Kenmore Refrigerator - Instructions

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

We logged on looking for a possible cause and solution. We found your website, diagnosed the problem, ordered the part and it came in two days. You even had a step by step video on how to change out the part. Kudos to you. Thank You

New part was not needed, when I removed lower closing cam the lower part of the closing cam attachment screw had worked it's self lose. So it just needed to be re-torqued. That took care of the problem.

We suspected the thermostat assembly was the problem. We reviewed the video provided by PartSelect and accessed the thermostat assembly. To ensure the thermostat assembly was likely the culprit, we used a multimeter to test it. We ordered the assembly from PartSelect and were pleasantly surprised at the speedy delivery. Using the same video, we replaced the assembly and put the refrigerator back together. Thank you so much for saving us money we didn't have for the repairman. We will be ordering again soon to repair a leaky waterline and ice maker.

I was cleaning my refrigerator. When the glass shelf was being cleaned it barely bumped the bottom of the sink. There was no water in the sink. The shelf exploded into thousands of small pieces simular to a car windshield. I was devastated! I went online and ordered a replacement that same day. The next morning I was on my front porch watering plants when a delivery truck pulled into my driveway. It was the replacement shelf. I cannot believe the fast service. Thank you.

I was really surprised. It was easier than I thought. Once I l loosened bolts with nutdriver the old gasket came out with no problem. To put the new gasket on I started at the top. I just slid the gasket lip under the metal brackets on the top and then the bottom. Next I slid the gasket lip under the metal brackets on the sides. I started tightening the bolts on the top and then the bottom. I did the sides last. I don't know about you but I had set aside the whole day for this and it only took 2 hours.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

I watched your repair video, read the instruction enclosed with the icemaker and made the repair in about 15-20 minutes. There is an issue that others need to be aware of once the water pump is repaced and the tubing is connected and the icemaker is installed and turned back on; it take 20-30 minutes to pump the air out of the line and the for the water to actually fill the the fill tray (you made the install correctly, the delay in filling is not covered by either the video or the book just be patience don't disconnect and reconnect anything it will eventually fill and make ice and less than 48 hours). This vendor offers 4 star customer service at a fair and resonable price (I priced the parts separately prior to purchase and the kit is the way to go). I received the product within 3 days, shipped groung delivery. I would use your products and online service advice for installation on other appliances in the future if needed. You have earned my trust, and repeat business in the future; and I will gladly recommend you to others. Your customer focus and service is second to none. I am a fully satisfied customer!!sincerely, a. Walker

Remove all items from door. Remove bolt holding plastic cover on top hinge. Support door and remove 3 bolts holding hinge. Lift door off lower hinge pin. Remove bolt holding both cam assy's and pry the one on the door out with the screwdriver. Replace both with the new cams, place door on lower hinge pin, place upper hinge pin into door, loosely insert the 3 bolts. Align the door, tighten the 3 bolts and replace plastic cap/bolt. Put the food back in the door and you're done. The only nut-driver needed is 5/16" and the screwdriver is only needed to pry out the cam that's located on the door itself.

The evaporator gan motor would work sometimes, but not always, so it took a while to be sure this was the problem. First ruled out thermostat and defrost timer. Also observed build up of ice on coils, so I knew compressor was working. Once I isolated problem to evaporator fan ( by observing stuck once, and seeing how it didn't spin freely) replacement was easy. In fact, since we were able to keep the unit running by watching the old fan and ensuring it was working while waiting for the new one to arrive, I was able to swap them out, plug unit back in and start it up before the ice in the bin even had time to melt! This repair saved me hundreds in repairs, and even more if I had to buy a new fridge, because the new units are too tall for my kitchen space.

Pulled out old drawer. Slid in new drawer. Super easy!

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

pulled door off like video showed and undid the small bolts holding cams on and put new on. It was real easy. Thanks for youtube video

Removed the back lower cover, behind the fridge. Uncliped the wiring. Removed the motor, (3 Screws).I did check the new motor before removal of the old one, to verify the older motor was the problem. After removal of the fan & motor. Removed the fan and placed it on the new motor, three screws later, plugged up the wiring, (I didn't changout the wiring, and the Refrigerator is good as new.

First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.