10648062895 Kenmore Refrigerator - Instructions

Heard double clicking sound every couple minutes. Unplugged unit then using a coil brush, cleaned all dirt, lint, everything from bottom of fridge. Finished with vacuum cleaner. Located start relay. It was on the left side of the compressor. Pulled relay straight off of compressor, much like a plug from a wall. Unhooked two wires from relay. No need to disassemble old relay. Parts received from partselect.com go back onto compressor individually. Using the instructions provided, from the kit, select the correct parts for your unit and carefully attach them to the compressor. Plug in the wire to the relay, then following the instructions, attach the jumper wire and plug into the relay. The cover in the kit is a little tricky to put on but it will fit. Took me about 15 mins and the hardest part was getting the old part off. Plugged unit back in and it started right up. 24 hrs later, everything is working great!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

internet search

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Just replaced the thermostat and is working perfectly. I would have to tap cooler knob and it would kick on. when it ran it ran well. So i knew it had to be electrical.Put in new thermostat and is working great!

Watched the video, followed the instructions, took my time and paid attention to what came off where, and viola. Not quite as easy as the guy in the video, but then it was my first time! Bottom line is: it worked. Refrigerator/freezer now maintains temperature exactly as expected, and I saved hundreds. Thank you!

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

This is a very easy fix. Begin by emptying the contents of the door. Then, just remove hinge cap and remove the three hinge screws. The door can then be lifted off the hinge pin and placed on its side. Once this is done, replace the two can pieces (one on the door and one on the frame). Then just lift the door back in place and secure the hinge. This job can be done by one person (maybe two if you need help place the door on a work surface) and will take just 15 minutes.

We bought the fridge used and immediately see why it was being sold. But ordered a new thermostat and with Part Select's instructional video was able to replace the thermostat. I should mention it was my first attempt making any repairs to a refrigerator. It was fairly straightforward project.

Took out the door bins, 1 bolt on the plastic cap, 3 bolts on the hinge, took the door off, replaced cam at the bottom, all same size bolts, reset the door spent longer time cleaning the door selfs all done by my self in less than 30 min. others said it helped to have second pair of hands "my wife would of just got in the way :)"

Fowolled the video instructions except it was necessary to disconnect the damper control rod to correctly install the capillary tube. the defrost timer was extremely easy to replace after determining the correct terminal for the black motor lead. The side by side is working great with the new parts and I would recommend your product and web site.