10647022791 Kenmore Refrigerator - Instructions

Followed the example on the video and everything fit in place without any problems. Only issue is that on a double door fridge the freezer is rather narrow so there isn't much room to work making it was a bit difficult to access the mounting screws.

Removed cardboard, Removed 4 bracket mounting screws, Removed plug, Removed screws securing motor to bracket. . Installed new motor on bracket, Installed fan on motor shaft , installed new pigtail on motor, Installed new assembled motor and bracket, Hooked up pigtail to electric supply, Installed cardboard, Plugged in to power supply and Voila, not even one foul word during the whole process. Note: watch the factory video. Thanks.

Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

I went on line to find the symptoms for what I was experiencing and went to web and entered the "KSRA" alphas and this list came up. I followed the explanation on video and it was identical. Good stuff.

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

Technically, the repair did not require specialized knowledge. However, replacement of the motor required some effort. Because the motor is located at the bottom of the unit in an area with copper tubing & wiring hindering access it was physically difficult to remove and then replace the motor. A problem arose because the shaft on the replacement motor was larger than the original motor's. Thus the fan would not fit on the new motor. Luckily, I found a fan locally that fit the motor. It would be very helpful if a fan was included in the motor kit. The ref. is now running smoothly

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Googled for a solution to how to fix a refrigerator door that would not close. Was directed to a video from PartSelect. Was wrong brand, but I got the general idea. Then, I looked up a refrigerator repair for Whirlpool. Called PartSelect with my model number and ordered a Cam Kit. Total cost shipped $20. Arrived in two days during the Holidays! Nice! (Ordered 12/23, Arrived 12/26). Opened package, fired the video up. Fixed in 15 minutes. Amazing!

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.