Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lights inside refrigerator not working
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
I was clening my uprght freezer and noticed that it was preped for an icemaker. I first went to the Whilpool website and could not find my part as my freezer was a 2008 model.
I saw PartSelect on the search page and went to thier site. I put in my modle number of the Whilpool Ice maker kit that was on the back of my freezer. PartSelect had the part in stock and approx $18.00 less than the other kits listed on the Whilpool site (that did not match my kit number). I orderd the kit on Sunday and it arrived on Wednesday. It took less than and hour to install. Every part I needed was included. The following day I installed the water line and now I have an extra icemaker.
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Had to replace a hose connector at the base of my refrig/frreezer
Perhaps a helpful hint:
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection. I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
The light switch on the refridgerator broke - no light.
Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.
The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.
I removed the ice bucket,the gear is located under the ice bucket and engages when ice bucket sits on it and turns the tray for ice to fall in the shute,2 screws to remove and the gear comes off and I put the new one on and put the screws back,very easy to do, total time 5 minutes,repair man wanted to charge $114 for the part and $100 for labor,I did it all for $25 thru this site,I love this site,it gsaved me alot of money,thanks partselect.,
The repair was so simple. I removed the old icemaker in about 3 minutes and unpacked and installed the new one is about 10 minutes. It was literally a matter of removing a few screws! Eady to follow instructions!
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Ice maker has stopped making ice and made a loud banging sound
I turned the water and electricity off for the refrigerator. (not sure if this is necessary but is safer) Remove the ice bucket. Cover the Ice auger with a hand towel to catch any screws which my get dropped. Remove four Philips screws holding plastic cover to inside of the door. there are no clip/snaps to worry about but on/off switch needs to be un plugged. Remove cover. Remove two nut head screws holding old ice maker. Remove wiring harness from ice maker and lift ice maker up and out. There are two tabs on the door. Unplug the wiring harness from the ice maker..
Installation: Press the wiring harness into clips on the new ice maker. Install ice maker onto door insuring it is over the tabs on door and the holes for nut screws line up. Plugging the wiring harness in and install two screws.
Plug on/off wiring onto switch and press plastic cover onto inside of door. Take care that it fits inside of rubber door seal. Install four philips screws. Remove hand towel and install ice bucket making sure the ice maker is switched on. Close door. Turn on water and electricity.
This took me 25 min. and I am sure would go faster if I had had instructions.
My refrigerator took awhile before it started to make cubes but has been working like new ever since. This task is easy go for it.
This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!
From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one. But Parts Select is a great place to order from. Thank you.
My icemaker is on the freezer door. Open the freezer door and remove the ice bucket and turn ice maker swith off. There is a plastic cover you need to remove just 4 screws then work cover a little and it will pull out. You need to disconnect the wire connector for the on/off switch for icemaker. set cover aside. Now the ice cube tray is exposed. On the right side there is another wire connection unplug this also. There is a small wire cable on top of ice tray it just pops off tray and stays there. Under ice tray remove 2 screws and lift up and out to remove tray. to install new tray align clips on top and screw holes on bottom and reattache 2 screws. Now refit the small wire cable on top to new tray and also reconnect the wire connector on the right. To reinstall cover reconnect the on/off wire connector and push cover back on. Make sure cover is on the inside of door seal. Reinstall the 4 screws turn the on/ff switch to on rinstall the ice bucket and close the door your done.