Models > 10646039800

10646039800 Kenmore Refrigerator - Overview

Get Parts and Repair Help for 10646039800

If you know the refrigerator repair part you need, you can browse the list of all parts on the 10646039800, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 10646039800 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$114.64

Ice Maker Assembly - 8 Cube

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and...

$2.52

Light Bulb - 40W

Sold individually.

$143.96

Electronic Control Boards - Emitter and Receiver

This set of two electronic control boards contains both the emitter and the receiver. These boards tells the icemaker when it's full and that it has to dump the ice, and it also te...

$50.59

Ice Door Kit

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

$20.36

Dispenser Grille

This black grille is located on the bottom of the ice/water dispenser to catch the overflow.

$54.43

Water Filter

This filter is used on side-by-side refrigerators with the push button in the front bottom grill. It reduces cysts, chlorine, taste, odor, lead and micro particles.

$27.87

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$16.63

Water Filter Cap

This black cap covers the water filter.

$9.60

Micro Switch

$69.50

Shelf Frame with Glass

This part is also known as Cover.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker stopped functioning

  • Customer: Phil from Auberry CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 243 of 254 people found this instruction helpful
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the right side. You're do... read more

Ice Maker would not stop making ice.

  • Customer: Vince from El Cajon CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 122 of 134 people found this instruction helpful
First, I tested the ice maker "switch" that actually just covers the beam that regulates the ice maker. In the "off" position, it still made ice. Then, I removed the three screws on the cover over the transmitter and disconnected the circuit board at the wire connector. It stopped. After ordering and receiving the new transmitter and receiver boards, I repla... read more

Fridge was getting too warm, ice buildup on coils.

  • Customer: Cathy from Winter Park FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 79 of 87 people found this instruction helpful
WARNING: REPLACING THIS PART REQUIRES CUTTING AND SPLICING ELECTRICAL WIRES. RISK OF ELECTRICAL SHOCK OR FIRE. DO NOT ATTEMPT THIS REPAIR IF YOU ARE NOT EXPERIENCED WITH ELECTRICAL WIRING.

Part Info:
The bi-metal strip is clipped onto the evaporator coils and is designed to regulate the defrost coil temperature. If it is not functioning prope... read more