10646023800 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice maker stopped making ice.
After determining by the flashing light code what the problem was, I ordered the parts. Once the parts arrived, it took 15 minutes to install them by the instructions that came with them and two hours later I was making ice again. Very easy repair and there is a video on the website that shows exactly how to do it.
Parts Used:
-
Walter from Gibsonville, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker went gaflooey
figured it was either the emitter/receiver or the control module.. even tho the online stats said it was probably the control module, i had a gut feeling (along with a volt/ohmeter) that said it was the emitter..... ordered the part.. came in 2 days..... six screws..... BOOM DONE !!fresh ice !!!!!ohhh what afeeling !!! pete s.
Parts Used:
-
peter from summit, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No Ice- Drive Gear On Ice Makes Broken Off
The video on your web site is great!! I had removed old ice maker and found that the main drive gear was broken off. Rec'd new one in 2 days remove bottom cover to put on new ice maker reinstall. Thanks for the help and great service!!! Tom
Parts Used:
-
TOM from ZANESVILLE, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken cap on water filter
With new cap, align slots on cap with grooves on water filter, and snap in place. Easy.
Parts Used:
-
David from Wiliamsburg, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice maker would not send ice through the dispenser
Opened the freezer door. Removed the ice bin from the freezer compartment. Removed with a nutdriver the two screws holding down the shaft holder (the triangular white plastic piece). Removed the shaft holder and the circular seal underneath. Pulled the hexagonal metal shaft up and out of the dispenser motor. Installed new circular seal and reinstalled the plastic shaft holder, etc..
Parts Used:
-
jonathan from austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Ice maker broken.
Ordered the ice maker assembly..received it within 4 Days of ordering it.It took less than 15 minutes to install.Removed the screw that holds the wiring cover.pulled the old ice maker out.unhooked the wiring harness from the old one.unscrewed the bracket from the old ice maker installed it on the new one.Plugged the new ice maker in slid it in put the wire cover back on.It was making ice within 30 minutes. Thanks partselect.
Parts Used:
-
Ken from Boise, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
I accidentally broke the arm that distributes the cubes to the ice bucket about a year ago. Just recently, the malfunction caused the entire thing to freeze up because the frozen cubes weren't cleared from the ice tray.
Remove 1 screw from the cover that hides the wiring harness, pull out the assembly and disconnect it. Swap the bottom mounting tray to the new ice maker and reverse the process. Way easier than I anticipated. No need to freeze your hands in the freezer, once you have the old one out you're working on the counter.
Parts Used:
-
Timothy from Brunswick, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Water filter cap on my Whirlpool refrigerator was inadvertently disposed of in one of my earliest filter change efforts. I needed to replace it for esthetics and personal peace of mind.
Ordered the replacement filter cap. Received it, cut open plastic shipping envelope after unsuccessful attempts to tear envelope by hand, snapped cap in place; Wallaah, project completed successfully!!!
Parts Used:
-
Theodore from Albukuerque, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Parts Used:
-
Don from Laramie, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Parts Used:
-
Steve from River Edge, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice would not dispense through front of door. There was no sound when the lever was pushed either, however, the water dispenser next to it worked fine.
Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.
Parts Used:
-
John from Cresskill, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice dispenser would not spin, shaft worn down
The hexagonal shaft had been worn down so that the edges no longer could be gripped by the teeth on the ice dispenser bucket. Remove the the two screws underneath the bucket. Use pliers (if needed) to pull out ht sold shaft. Slide in the new shaft, and twist until it drops into place. Replace the two screws and you're all set!
Parts Used:
-
Jon from Coppell, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Parts Used:
-
Anthony from Fairport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Icemaker would not stop making ice.
Purchased the recommended/required electronic control boards for the sender and receiver. Removed the units and replaced the boards and reinstalled. Icemaker is working fine since the repair.
Parts Used:
-
Barry from Henderson, NV
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not getting ice
Replaced the optic boards - no lights working. Still no ice. No water coming into ice machine. Followed instructions on your website and diagnosed frozen line. Took ice machine out, used hair dryer, reinstalled and we have ice! Thank you so much for saving us a repair bill!!!!! Buying the part from you was very easy and your videos were excellent!!!
Parts Used:
-
linda from lambertville, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!