10645423801 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water stained drip tray
pop in and presto! simple, no tools required, perfect fit.
Parts Used:
-
Laura from Knoxville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was getting warm
Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.
Parts Used:
-
Mack from Los Banos, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
door would not seal well
replaced cam on door. would have replaced mating cam on ref box if i knew there were two pieces.
Parts Used:
-
Edward from Laurel, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Kick Plate Clip Broke
On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.
Parts Used:
-
James from Virginia Beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
icemaker stopped working
I did not have voltmeter to test for problem. Internet sites suggested the most common problem is the circuit boards--a sender and a receiver which detect when the ice bucket is full. I could only buy as a pair (about $94). I removed two screws of cover of receiving unit, detached the coupler, replaced the circuit board. Icemaker now works. The sender was obviously still good.
Parts Used:
-
Thornton from Highlands, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Cracked drawer
Ordered part over the phone and received it two days later.....excellent service
Parts Used:
-
Carolyn from Truckee, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Thermostat was broken Flap was broken on the door and Sensor was broken off the ice mold on
Took The icemaker apart saw what parts needed to be replaced ordered them online put it back together Found the person I dealt with on the phone to be very knowledgeable very happy with the company Now the ice is flowing
Parts Used:
-
William A from Coral Springs, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace Water Filter
-
Eugine from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
frozen ice would not dispense
the tutorial is perfectwatch Steve. The boards were bad but coincidentaly so was the motor/control unit. I satrted with the boards, got my LED codes back to normal but still could not dispense. Installed the motor/control unit and had cubes dropping in 15 minutes. Great service, great tutorials.
Parts Used:
-
EDWARD from OCEANSIDE, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The ice maker failed
The helpful Partselect video showed a slightly different model, as my icemaker uses optics instead of a bail for shutting off the icemaker. I ordered new optics based on a a customer description that, if the light on the right hand side of the freezer door jamb was blinking 2 flashes followed by a pause,it indicated that the optics were faulty, so I ordered and replaced them. This did not solve my problem. Then on-line I found further information that said I should close the flapper on the left side, and if the light was steady (which it was) the optics were OK. I then ordered the motor unit. I unscrewed the single screw under the right hand side of the track with a 1/4" nut driver, but found that sliding out the ice maker involved a little wiggling and prying, and, because it was awkward to disconnect the electrical connection, I found that it was not necessary to disconnect it. Then, after removing the end cap, it was a straight forward process to replace the motor, while adjusting the shaft to line up. Then,reverse all procedures and I now have ice. Success!
Parts Used:
-
Alan from Edgartown, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
freezer was freezeing up
unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.
Parts Used:
-
phillip from palmyra, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Ice maker will not make ice, the water does work on the door
Replaced the Electronic control boards first, emitter and receiver, and that did not fix the problem. I then order the Control board/motor assembly in the ice maker, this did fix the problem and after a couple of hours I had ice. The repair was easy and the videos on the web site show you step by step.
Parts Used:
-
Christopher from Thurmond, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Coating of Mold deterioated and mold leaked into ice tray
-
Dwight from Bossier City, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Ice maker wouldn't harvest
Swapped out the emitter and receiver control boards. Super easy. Watched the video on how to do it on your website.
Parts Used:
-
Jim from Denham Springs, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker was not making ice
used the video on your web site. also read the overview made things really simple
Parts Used:
-
William from princeton, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!