10645422800 Kenmore Refrigerator - Instructions

The replacement was easy, especially after watching the install video. Saved over $200 by purchasing the part at PartSelect and doing the install myself. Will use PartSelect again in the future.

I did not have voltmeter to test for problem. Internet sites suggested the most common problem is the circuit boards--a sender and a receiver which detect when the ice bucket is full. I could only buy as a pair (about $94). I removed two screws of cover of receiving unit, detached the coupler, replaced the circuit board. Icemaker now works. The sender was obviously still good.

Ordered part over the phone and received it two days later.....excellent service

Had repair people in a year ago and could not find problem-They changed water flow meter valve-(costly for parts and labor) Did not solve problem!I needed ice so purchased external ice maker used for 1 year-Told myself I know it is the ice maker-Got on line and ordered from PART SELECT! Only took a few days for part to arrive-I had watched video for changing parts out on line-Took only 10 minutes to duplicate video-In 45 minutes I had first ice in over 12 months-Has been working perfect since installation!Don Smith

Took The icemaker apart saw what parts needed to be replaced ordered them online put it back together Found the person I dealt with on the phone to be very knowledgeable very happy with the company Now the ice is flowing

Followed the instructions in the PartSelect video. It was so easy. Replaced the old ice maker on Monday. Visited a friend on Tuesday. Her Kenmore Frig's ice maker was broken, would not make ice. I told her how easy it was to fix and ordered the part for her today. It should be here by Tuesday and I will install it as soon as it comes in.

Peice of pie

the tutorial is perfectwatch Steve. The boards were bad but coincidentaly so was the motor/control unit. I satrted with the boards, got my LED codes back to normal but still could not dispense. Installed the motor/control unit and had cubes dropping in 15 minutes. Great service, great tutorials.

I watched the quick video once to see the type, if it matched mine, and the difficulty. I went ahead and ordered the part and within minutes, I had the ice maker installed. The video was so well designed, I only had to watch it once!

Checked the hose above the icemaker to see if water was frozen. Ran the freezer at a lower temp to see if lines would unfreeze. Took a wild guess that a component was broken in the icemaker, but it was cheaper to get the entire assembly anyways. Removed about 4 screws under icemaker, disconnected icemaker, jiggled and slid the icemaker and tray out, traded out icemaker assemblies, and put it all back, probably took 10-15 mins, and it made ice again!

Remove ice maker from refrigerator,remove damaged part,replace with new one.

The helpful Partselect video showed a slightly different model, as my icemaker uses optics instead of a bail for shutting off the icemaker. I ordered new optics based on a a customer description that, if the light on the right hand side of the freezer door jamb was blinking 2 flashes followed by a pause,it indicated that the optics were faulty, so I ordered and replaced them. This did not solve my problem. Then on-line I found further information that said I should close the flapper on the left side, and if the light was steady (which it was) the optics were OK. I then ordered the motor unit. I unscrewed the single screw under the right hand side of the track with a 1/4" nut driver, but found that sliding out the ice maker involved a little wiggling and prying, and, because it was awkward to disconnect the electrical connection, I found that it was not necessary to disconnect it. Then, after removing the end cap, it was a straight forward process to replace the motor, while adjusting the shaft to line up. Then,reverse all procedures and I now have ice. Success!

We followed the video which was a great help. The only difficulty we had is the black rubber tube (water fill tube) was hard to get into the new ice maker. But finally got it. The new icemaker works wonderful! No more buying ice!

I researched my problem online and watched a video of a ice maker installation before I attempted my repair. I ordered the part at 11am Thursday morning and the part arrived at 10am Friday morning via Fed Express. First, I removed the bracket the was holding the ice maker in place. Second, I slide the ice maker out. Then I disconnected the old ice maker. Next I used a screwdriver to remover 3 screws for the plastic housing, since it was need for the new ice maker. I plug it in and put the bracket back in place. I went out for a couple of hours. I returned home and ran to the freezer.I open it and I found ice cubes. I was finally able to throw out my ice cube trays. Boy I hate them!!! Don't fear this repair it's simple and very cheap. I saved roughly $160.00 by doing it myself. I will use this company again since they were great

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.