10644554401 Kenmore Refrigerator - Instructions

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

First I checked the compressor, very hot to the touch & not running. I unplugged for a few minutes to cool & when I plugged it back in, it started for maybe a second or two. Then I unplugged the relay from the compressor and new instantly it was fried. So I decided to google the issue which led me too partselect.com and I then realized this relay is called the start device/Relay and it also provides overload protection for the compressor. When I received the part or parts in this case, they came in a small box which included 2 combo relays, 2 overloads, 1 ptc start relay, 1 jumper wire, 1 electrical cover, 1 instruction sheet. By using the number on the compressor I was able to see that I needed to use the ptc start relay & one of the 2 overloads which plug onto the compressor & I needed to use the white jumper wire as the terminals were a different size on the ptc relay. At first I was a little confused because I unplugged one relay and the replacement was two separate parts. Had to read instructions carefully several times to make sure I was using the correct overload and ptc relay. I plugged in the fridge to test & it worked great so I unplugged and installed the electrical cover, reinstalled cardboard cover on back of fridge & I was done. Two weeks later fridge is working great!! Hope this helps.

I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.

It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.

Per instructions

I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.