10644423601 Kenmore Refrigerator - Instructions

The replacement ice maker water inlet was taller than the original. I had to disassemble both the new and old unit to replace the new water inlet with the old one. The video was very helpful in troubleshooting, removing and installing the unit.

Watcheda U-Tube type video of how to repair the unit. This was very helpful in that it identified a screw that had to be removed but was not visible upon my initial observations. Also it mentioned that you had to re-use some of the original hardware in order to complete the replacement. My only complaint is that I believe the failed motor could have been replaced for about $15 but I was not able to find that specific part in any catalog and opted to replace the entire unit. Overall I am extremely well pleased. Everything now works fine.

Followed the video. only problem old ice maker was frozen in place. Had to thaw out in order to slide old ice maker out of slot. other then that, new one is working fine.

research of company website showed parts to buy (per percentage of failure) and how to install those parts I viewed video on installation of parts and did the job, it was a snap

Web site is fantastic, I used web site to figure out my problem and order parts, I also used web site on how to install which made it a snap to do repair Ice maker up and running, all replacements parts were factory which fit perfectly

easy,remove old parts installed new parts,icemaker started working properly.

Followed instructions posted on your site. It was straight forward and very simple to complete.

Initial diagnosis incorrectly led me believe the problem was with the optic eye. After replacing the optic eve and still no ice, I realized the problem had to be with the actual ice maker itself. The removal of the old ice maker and installing of the new one took less than 5 minutes. This of course was after watching the repair video first. I still feel that I saved money by doing the repair myself instead calling in a appliance repair man, even with the added cost of the probable unneeded optic eye replacement. I am very satisfied.

The ice maker quit working about 4 years after we purchased this refrigerator. I asked several contractors if they knew what the problem could be. All believed it had something to do with the water line being stopped up. However, when I looked at the water line, it seemed fine. Thankfully when I googled about repairing this refrig, I came upon this website. It stated statistically that the Icemaker assembly part was the problem. Guess what? Replaced it and it works! The repair was a little tedious, so I got my next door neighbor to help. He has a few moments struggling getting it out and the new one in, but overall, it was not too difficult. I believe I could have done it with the video's help but certainly would have taken me longer.

I was cleaning my refrigerator. When the glass shelf was being cleaned it barely bumped the bottom of the sink. There was no water in the sink. The shelf exploded into thousands of small pieces simular to a car windshield. I was devastated! I went online and ordered a replacement that same day. The next morning I was on my front porch watering plants when a delivery truck pulled into my driveway. It was the replacement shelf. I cannot believe the fast service. Thank you.

i followed instructions on video it went real simple except for the small area to work in.

Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

I actually purchased an ice maker, a combination start device & a run capacitor. I watched the 2 videos which were very helpful, in fact I may not have been able to do this if I had not watched the videos first. It took me step by step. It couldn't have been more simple. I replaced the start device & the run capacitor first just to make sure my fridge would cool again, then when it did, I replaced the ice maker. I saved myself a service call ($59.95) and the labor to replace the ice maker & other parts($140)and that didn't include the parts! By the way I'm female and 71 years old. So if I can do this anyone can.

Ordering through this site was extremely easy. They sent the right part and I received it very fast. I'm very impressed.

Open freezer door and close flap on the left being sure not to block the infrared beam. If red light goes solid in a few seconds the Emitter receive and xmit boards are good. Unplugged fridge, Took the ice machine out took off the motor/controller cover and jumpered the two test points together with a short length of insulated wire. place the ice maker back on bracket to free up my hands and plugge in the fridge, turned ice maker on. Closed the flap and ensured red light was on solid and I was not blocking the beam... the motor control wheel did not turn slowly/cycle as it should have with the jumper inserted... Motor/controller assembly was bad. Pulled out icemaker and noticed some corrosion in the ice tray so ordered the entire ice maker instead of just the motor/control assembly... cost only about $30 more. New ice maker arrived and I installed, took about 10 hours before it got cold enough and began making ice.