Models > 10644423600 > Instructions

10644423600 Kenmore Refrigerator - Instructions

All installation instructions for 10644423600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644423600
616-630 of 665
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken water fill cup

  • Customer: augustine from cedar rapids IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

freezer was freezeing up

  • Customer: phillip from palmyra VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

Ice maker will not make ice, the water does work on the door

  • Customer: Christopher from Thurmond NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Electronic control boards first, emitter and receiver, and that did not fix the problem. I then order the Control board/motor assembly in the ice maker, this did fix the problem and after a couple of hours I had ice. The repair was easy and the videos on the web site show you step by step.

Door not staying closed

  • Customer: Josh from Snohomish WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

Ice would not come through

  • Customer: Eleanor B. from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
During our blackout the ice melted down the rod so it would not turn to release the ice to drop into your glass because of the water so we replaced the bottom portion of the ice maker which is on the inside of door under ice container and everything works great now. This happen before because of blackout and ice melted and ruin the and rusted the release

Coating of Mold deterioated and mold leaked into ice tray

  • Customer: Dwight from Bossier City LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video on Parts Select and it was a breeze.

ice maker stopped making ice

  • Customer: Stan from Kenilworth NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Originally ordered parts I thought would fix ice maker. When I took apart the icemaker assembly I noticed and found the actual part that went bad. Called customer service and was able to return the parts I thought would fix the ice maker, without any problems. I ordered the correct part on the same call. Within a day or so the new part arrived and was installed within 15 minutes. Thanks to the instructions & comments posted on the "Instant Repairman" link. Awesome customer service that can not be bet.

Ice maker wouldn't harvest

  • Customer: Jim from Denham Springs LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Swapped out the emitter and receiver control boards. Super easy. Watched the video on how to do it on your website.

ice maker not working

  • Customer: Guy from Palmdale CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the two circuit boards

Fan became noisy and started wobbling.

  • Customer: James from Cave Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Ice maker not making ice.

  • Customer: John from Greeley CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced emitter and receiver boards. That did not fix the problem, ordered valve hope that is it.

Condenser Fan was making noise

  • Customer: Kerry from Franklin TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Condenser fan vibrated loudly while turning

  • Customer: Robert from Aurora IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

Ice maker not working

  • Customer: Harry from Colonial Beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As your video showed. Used kitchen knife to get connection tight

Water would not flow into icemaker and icemaker would not work.

  • Customer: Kenneth from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions given by your demonstration. I took the back screw off, dropped the wire plastic cover. I then used the screwdriver to push the two (2)slots in and pulled the icemaker out and then unplugged it. I believe unplugging it was a little hard because the plug was pretty well sealed together and frozen. After finally getting the plug apart I then pulled the icemaker fully out. After pulling the cover off and putting it on the new one per your demonstration, I then inserted it back in. I stuck my hand behind the icemaker and bent the hose with my index finger and thumb so that it would drop into the water tray and then slid the icemaker back in until it snapped back in the slots. I then put the plug cover back on and reinserted the screw. I forgot to mention taking the front cover off before removing the icemake and reinserting it after replacing the icemaker. I would highly suggest customers follow your demonstration, it paid off well. I watched it about 8 times before I received the icemaker in the mail. Oh by the way water started flowing into the icemaker with 4 minutes and ice started coming out in about 30 minutes. As the icemaker got colder it started producing the ice faster. It's a sweet sound hearing the ice drop into the container.
All Instructions for the 10644423600
616-630 of 665