10644422603 Kenmore Refrigerator - Instructions

I was cleaning my refrigerator. When the glass shelf was being cleaned it barely bumped the bottom of the sink. There was no water in the sink. The shelf exploded into thousands of small pieces simular to a car windshield. I was devastated! I went online and ordered a replacement that same day. The next morning I was on my front porch watering plants when a delivery truck pulled into my driveway. It was the replacement shelf. I cannot believe the fast service. Thank you.

i followed instructions on video it went real simple except for the small area to work in.

Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

I actually purchased an ice maker, a combination start device & a run capacitor. I watched the 2 videos which were very helpful, in fact I may not have been able to do this if I had not watched the videos first. It took me step by step. It couldn't have been more simple. I replaced the start device & the run capacitor first just to make sure my fridge would cool again, then when it did, I replaced the ice maker. I saved myself a service call ($59.95) and the labor to replace the ice maker & other parts($140)and that didn't include the parts! By the way I'm female and 71 years old. So if I can do this anyone can.

Ordering through this site was extremely easy. They sent the right part and I received it very fast. I'm very impressed.

Open freezer door and close flap on the left being sure not to block the infrared beam. If red light goes solid in a few seconds the Emitter receive and xmit boards are good. Unplugged fridge, Took the ice machine out took off the motor/controller cover and jumpered the two test points together with a short length of insulated wire. place the ice maker back on bracket to free up my hands and plugge in the fridge, turned ice maker on. Closed the flap and ensured red light was on solid and I was not blocking the beam... the motor control wheel did not turn slowly/cycle as it should have with the jumper inserted... Motor/controller assembly was bad. Pulled out icemaker and noticed some corrosion in the ice tray so ordered the entire ice maker instead of just the motor/control assembly... cost only about $30 more. New ice maker arrived and I installed, took about 10 hours before it got cold enough and began making ice.

Watched the video accompanying the ice maker replacement part. Took 6 minutes. Then, having gathered my two recommended tools, moved to the fridge. Had the new replacement installed and working in 4 minutes. Doesn't qet any better than this.

Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.

replace the emitter and receiver which is located on the left and right side of your freezer when you open the door. use a crosstip head screwdriver remove the 3 ea. screws on the emitter frame ,dothe same for the receiver. replace the electronic boards and reinstall.wait at least 30 minutes and listen for ice to drop in the ice bucket.

used the video on your web site. also read the overview made things really simple

I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

Used the trouble shooting off of YouTube and after finding that the heater was not at the right resistance, ordered a new ice-maker and installed. Very simple and a lot cheaper than going through Sears.

Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

Turn ice maker control off,hold up front cover remove two screws, remove cover, remove rear screw on the back right side, slide unit part way out, make sure flipper on left is out of the way, unplug connector on right, remove unit,remove bottom cover & put on new unit,install in reverse order, turn ice maker control on, done

I went on line and found your web sight. There was a list of the parts by number and I clicked on the rilght one. It brought up a video for repairing it myself. It was so simple. I just followed your instructions and within an hour I had ice. It makes so much ice I'm going to have to give it away. No really its great.