Models > 10644323400 > Instructions

10644323400 Kenmore Refrigerator - Instructions

All installation instructions for 10644323400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644323400
796-810 of 1,077
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker stopped making Ice

  • Customer: Glenn from Dowell MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off the icemaker and took out the hex screw at the back of the unit that held the cable guard. The ice maker was easy to slide out after releasing guide locks on each side of the unit. Pulled the unit forward and released the electrical connection. With the unit on the cabinet, I removed the motor housing cover. Took out the 3 scews holding it in place and the old motor was out. Just reverse the steps putting the new one in. In an hour or two we heard ice dumping into the holder.

The ice maker failed

  • Customer: Alan from Edgartown MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The helpful Partselect video showed a slightly different model, as my icemaker uses optics instead of a bail for shutting off the icemaker. I ordered new optics based on a a customer description that, if the light on the right hand side of the freezer door jamb was blinking 2 flashes followed by a pause,it indicated that the optics were faulty, so I ordered and replaced them. This did not solve my problem. Then on-line I found further information that said I should close the flapper on the left side, and if the light was steady (which it was) the optics were OK. I then ordered the motor unit. I unscrewed the single screw under the right hand side of the track with a 1/4" nut driver, but found that sliding out the ice maker involved a little wiggling and prying, and, because it was awkward to disconnect the electrical connection, I found that it was not necessary to disconnect it. Then, after removing the end cap, it was a straight forward process to replace the motor, while adjusting the shaft to line up. Then,reverse all procedures and I now have ice. Success!

no ice, motor not running

  • Customer: Randy from Mesa AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker, replaced motor and reinstalled. Very quick delivery of parts, fit perfectly.

ice maker stopped making ice

  • Customer: harold from new faifield CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the motor control assembly and it works great

Ice maker quite making ice.

  • Customer: Melanie from Northfield MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We followed the video which was a great help. The only difficulty we had is the black rubber tube (water fill tube) was hard to get into the new ice maker. But finally got it. The new icemaker works wonderful! No more buying ice!

Ice maker stopped producing ice.

  • Customer: phil from Huntingdon Valley PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I researched my problem online and watched a video of a ice maker installation before I attempted my repair. I ordered the part at 11am Thursday morning and the part arrived at 10am Friday morning via Fed Express. First, I removed the bracket the was holding the ice maker in place. Second, I slide the ice maker out. Then I disconnected the old ice maker. Next I used a screwdriver to remover 3 screws for the plastic housing, since it was need for the new ice maker. I plug it in and put the bracket back in place. I went out for a couple of hours. I returned home and ran to the freezer.I open it and I found ice cubes. I was finally able to throw out my ice cube trays. Boy I hate them!!! Don't fear this repair it's simple and very cheap. I saved roughly $160.00 by doing it myself. I will use this company again since they were great

Discolored tray

  • Customer: Blair from Argyle TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Got on your website and found our refrigs expanded layout and ordered the part. The removal and install was less than one minute Including the clean up.

Ice maker made ice but would not dump it into ice container

  • Customer: Danny from Martin GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the motor and everything is working great!

Ice maker stopped making ice - repair not successful

  • Customer: David from Lewisville TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

my icemaker quit making ice

  • Customer: Eugene from Jackson MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First off, the part I ordered arrived with broken tab. I called and had no problem getting a replacement unit mailed out right away. The video repair really helped a lot. Had a little trouble with the fill tube, it was a little hard to get inside the icemaker when installing the new one. Other than that, it was a piece of cake following the video instructions.

Ice maker just quit working!

  • Customer: Keith from Sanford ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

Wouldn't make ice

  • Customer: Randy A. from Ponca City OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video, then removed old maker and installed new one. Makes ice fine now. Thanks

Ice maker stopped working

  • Customer: Stephen from Lynnwood WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching a YouTube video I was able to determine that my ice sensor was working properly. I was getting water through the door dispenser so I decided to pull the icemaker. First I removed the 2 hex head screws holding the ice door which gave me access to the icemaker. I removed the hex head screw holding the electrical plug cover on the bottom right side and removed it. I then pushed up on a plastic tab on the bottom left side of the ice maker and slid the icemaker out so I could access the electrical connection. After unplugging the electrical harness(plug/socket) I completely removed the icemaker from the freezer. The white square end cover easily pulled off the icemaker exposing the control and motor assembly. After removing the 3 screws holding the assembly on I pulled the assembly off the end of the icemaker. Installation was as simple as assembling the parts in reverse order making sure that the ice delivery male shaft "flat" mated with the "flat" on the motor drive female socket. After reassembly I went for a bike ride and when I returned about 3 hrs. later I was happy to see my icemaker was making ice again. This is actually easier than it sounds if you have any mechanical apptitude whatsoever.

Ice maker stop making ice cubes.

  • Customer: Ken from Nampa ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I saw the question listed on your website with your recommended part to repair. Instead of ordering a whole new ice maker I took the chance and ordered the recommended part for repair. I saw the video and when the part came it was really easy to replace. I only wish I had found your website earlier and not gone without ice for as long as I did. Thanks.

Would not make ice

  • Customer: David from Surprise AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both the Ice maker and the control boards as It was for a rental and I did not want to make more trips then necessary to repair. I installed the new control boards and the ice maker and the refrigerator now makes ice.
All Instructions for the 10644323400
796-810 of 1,077