Models > 10644322400 > Instructions

10644322400 Kenmore Refrigerator - Instructions

All installation instructions for 10644322400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644322400
1,021-1,035 of 1,129
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ICE maker door hinge replacement

  • Customer: Theresa from Eagle River AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed two hex head screws, installed new part with nut driver for two hex head screws , very easy. I broke the tab off the hinge for the ice maker door when I installed a new ice maker the week before.

tab broken off ice guide. discolored and nasty looking. Ice maker had quit working also.

  • Customer: Jack from Casa Grande AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
First we bought an icemaker from Parts Select. That repair went very easy. The old icemaker the plastic coating over the metal had started to come off. We replaced the icemaker and I waited but didn't hear it fill the ice tray I was worried then that it was a valve that was mentioned on the website. The next morning my Wife told me, we have ice I was very happy. Easy to replace the ice maker just have to unplug ours at the icemaker itself, loosen 2 bolts and it comes right out. We just purchased this house and later while we where cleaning the dispenser paddles discovered that the ICE GUIDE the bottom tab was broken off and it was badly discolored so we quickly placed a 2nd order for a new ice guide and thought as long as we where doing that pop out the ice dispenser grille and replace that. They ship quickly and prices seem reasonable. Thank you Parts Select.

Discolored tray

  • Customer: Blair from Argyle TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Got on your website and found our refrigs expanded layout and ordered the part. The removal and install was less than one minute Including the clean up.

water stain on dispenser grill

  • Customer: luis from Grapevine TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the water stain on the dispenser grille was unsightly even after cleaning with baking soda and vinegar, hence, we purchased a new one. popped the old one out and put new one in. have used parts select in the past and their pricing was very competitive if not better than over vendors.

cracked and dingy tray

  • Customer: joe from lake worth FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unsnap old teay snap new one in very easy

water stained drip tray

  • Customer: Laura from Knoxville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pop in and presto! simple, no tools required, perfect fit.

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

NO LIGHT

  • Customer: Mary from Jefferson Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SOCKET OUT AND REPLACE IT WITH NEW ONE. VERY EASY. W SAVED ALOT OF MONEY DOING IT OURSELF.

Ice not coming out when pressing level outside freezer door.

  • Customer: Edgardo from Hackensack NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

door made clacking , thunking noise when opened

  • Customer: BILL from ADVANCE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

Had to completely remove the ice maker in order to install the replacement part

  • Customer: Leonard W from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Ice Maker quit working

  • Customer: Michael from Oroville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on your video to replace the coupling. The blades were not installed correctly so using your Diagram I reinstalled the blades. and now it works great . and I would like to mention that the shipping was overnight. Thank you for your help saved me a whold bunch of cash and time.

Coupling broken between ice bin and grinder unit

  • Customer: Dwight from Morehead KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the ice bin, removed small screw in bottom of grinder (visible from bottom). placed new coupling on shaft, inserted new screw and was finished. Super fast.

Coupler between ice tray and chute broken.

  • Customer: Leonard from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed your expert instructions, no problem. Less than 20 minutes.
All Instructions for the 10644322400
1,021-1,035 of 1,129