10644259401 Kenmore Refrigerator - Instructions

Went to the site to determine the problem and ordered the three most probable causes to my situation. replaced two of the items and had to send one part back because it didn't exist on my Model. Still did not run. Went back to the site and ordered the thermostat and the problem is resolved.

Took it out and slipped the new one in.

just remove the damaged one and replace with the new one---easy- breezy

Great video on-line - remove door by unscrewing bracket (3 screws) at top of door; the door magnet will hold it to the face of the frig until you are ready to lift it off... Lift door off and position horizontally across a padded table or sawhorses. The door is actually very light in weight. The cams at the bottom were easy to put on - use care not to overtighten the retaining screw. The top thimble takes a lot of time to "dig out" of the top of the door - hard not to mar and bend the door in this area. This took almost one-half hour to get it out!! Putting in the new one, use care to not cave in the door corner, not a lot of structural strength in the area. Once all the door items are in place, put the door back in place on the frig and replace the top bracket to hold it in place; watch to line up the gap between the frig and freezer door so it hangs straight. Check the two cams at the door bottom - they won't fit perfectly when the door is in the closed position and that is OK... IMPORTANT - the door should now close, but it won't automatically shut on its own until you load the door back up with your food items. Once the items are in place on the door you will see that it now closes completely with very little to no effort... just like it should. Hope this is helpful!!!

I Checked thermostat in freezer compartment for continuity I next checked defrost heater for proper ohms. both were ok. I assumed defrost control board could be only problem. changing control board located in upper right was simple ,pop off cover plate with small screwdriver remover four screws plug in new control board.

Just re-intall the new drawer. That's it. Thank you !!

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

Replaced the start relay in about 5 minutes and plugged the fridge in and it started working. Easy repair to get fridge working again.

removed the damaged unit and inserted the replacement.

Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

as told per compter

I vacuumed the back and underneath, hoping it will solve the problem, but after about 2 weeks of hoping I succumbed.... finding the proper wrench was the most time consuming. After removing the screws, the face plate removal was the most challenging. You have to pry the top part carefully away (we used a knife), after it just drops down. Used a flat screw driver to loosen the wire harness, after that the rest was less than child's play. We are still in the testing mode, but so far so good. Freezer freezes, ice maker drops the ice cubes (not melting), fridge is humming. Wish us good luck.

I followed the instructions provided on a video that was shown when I went to order the required parts. The video was very well done. It is very accurate.If you fololw the instructions you can make the repain in about 30 minutes. It was very easy

Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.