Models > 10644103300 > Instructions

10644103300 Kenmore Refrigerator - Instructions

All installation instructions for 10644103300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644103300
706-720 of 766
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

plastic catches broken off ice guide

  • Customer: Wanda from Glennville GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just remove old one which was really easy since it was practically falling off and replace with new one. It is a bit tricky because you are afraid of breaking the new one. Watch the video and you will be more confident. I was REALLY impressed with the shipping. I ordered on Monday afternoon and when I returned home Tuesday afternoon it was waiting for me on my porch , and this was the week between Christmas and New Year when everyone was fussing about not receiving packages. NOT ME!

Ice maker not working

  • Customer: Mercedes from Lyndhurst NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We replaced the ice maker with the help of the video, it was very helpful and it is working fine, thank you very much.

Ice maker stopped working

  • Customer: Kevin from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After viewing the very clear video. Remove the ice maker door by first lifting the door and pressing in on the hinges. Remove the screw in the back lower right of ice maker with a one quarter inch nut driver and lift out the cover to expose the wiring harness. Pull the ice maker unit forward and out and reach behind it to pull out the wiring harness plug. The plug only comes out if you depress the small "push clip" in the center of the harness plug. Turn the old ice maker unit upside down and remove the three screws again with the one quarter inch nut driver to lift off the plastic cover. The wiring harness plug need to be pushed through the plastic housing to remove the plastic cover completely. Reinstall the plastic cover on the new ice maker. Reverse the procedure and install the new ice maker. This is really a simple repair if you watch the video.

Ice Maker running over, water/ice fall in freezer

  • Customer: VICTOR from MARANA AZ
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Used hair dryer to melt ice so I could remove old ice maker. Used old icemaker Model #2198597 to order new ice maker. New ice maker water funnel that catches water that goes into the ice mode was higher then the older one. Everything else looked ok. I contacted parts select and was told, if I took the new icemaker apart and it didn't work I could not return it. After three phone calls I was told that I could keep the new ice maker and they would refund my money. So I was left with take the new ice maker apart or cut down the funnel. I cut down the funnel and slid the new ice maker into place. My second choice was to take the new ice maker apart & put on the old funnel. Parts select (Susan) has sent me an email that I would get my money back as the part was not correct. I feel bad about this the way it worked out. It took me about 20 minutes to cut the 1/2 inch off the new funnel.

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Ice maker in freezer stopped making ice

  • Customer: John from Washington DC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the steps in the video posted on webpage describing the part. I watched a sement, performed the steps, and then watched the next segment. I spent more time trying to locate my nut driver set then I spent doing the actual repair.

No ice

  • Customer: Janis from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

coupling broke apart

  • Customer: Rodney from Troy IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
simple remove and replace

Clicking sound when opening door

  • Customer: mike from richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

Ice maker not working

  • Customer: Jeff from Wingo KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Our ice maker would work a few days then it would freeze up because it ran to much water in. I finally called Parts Select. The gentleman found the correct parts right away and I had them in two days. Took about 30 minutes to change out with a new unit. Only cost about 120 dollars. If I had known it would of been that easy and that cost effective I never would have took the time to un thaw it so many times with the blow dryer. Buy the new one, quick repair and gets rid of the head ache. Besides you will have ice when you need it. Good luck

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

Ice Maker would not eject ice from the ice tray.

  • Customer: Todd from Meridian ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

NO ICE- DRIVE GEAR ON ICE MAKES BROKEN OFF

  • Customer: TOM from ZANESVILLE OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
THE VIDEO ON YOUR WEB SITE IS GREAT!! I HAD REMOVED OLD ICE MAKER AND FOUND THAT THE MAIN DRIVE GEAR WAS BROKEN OFF. REC'D NEW ONE IN 2 DAYS REMOVE BOTTOM COVER TO PUT ON NEW ICE MAKER REINSTALL. THANKS FOR THE HELP AND GREAT SERVICE!!! TOM

Ice maker stopped making ice

  • Customer: Richard from Stephens City VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

Ice maker broken.

  • Customer: Ken from Boise ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered the ice maker assembly..received it within 4 Days of ordering it.It took less than 15 minutes to install.Removed the screw that holds the wiring cover.pulled the old ice maker out.unhooked the wiring harness from the old one.unscrewed the bracket from the old ice maker installed it on the new one.Plugged the new ice maker in slid it in put the wire cover back on.It was making ice within 30 minutes. Thanks partselect.
All Instructions for the 10644103300
706-720 of 766