Models > 10644102300 > Instructions

10644102300 Kenmore Refrigerator - Instructions

All installation instructions for 10644102300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644102300
61-75 of 759
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Heater on Ice Maker stopped working.

  • Customer: Andy from Lorena TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
Repair was easy and producing ice within five hours.

NO ICE

  • Customer: Bob from Camby IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 10 people found this instruction helpful
Removed one screw, carefully removed the unit, unplugged it and reversed the process to install. My only issue was the picture of the part I ordered was not the same as I received.

Ice maker quit after 3 years

  • Customer: Jeffrey from Topeka KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 11 people found this instruction helpful
I removed the two screws holding the cover door, then the three on the uder side of the icemaker assembly. I carefully worked the old unit out; it was a tight fit. The most difficult step involved disconnecting the power assembly. Due to the space, it was hard to get hold of each side of the clip to pull it out. After the old unit was out, just reversed the steps and had the first batch of ice in less than an hour. (I washed the new unit with warm water and soup as it had grease/lubricant on it when taken out of the package).

Icemaker quit making ice

  • Customer: Bobby from Mokena IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 14 people found this instruction helpful
I found a repair guide online to check the resistance of the motor, thermostat, and heater mold. The resistance of the motor and heater mold were both a little off from their recommendations. I had an assumption that it was the motor but I decided to just buy the whole assembly basically for spare parts and I didn't feel like messing around with it any more. The new icemaker was not just a drop in replacement as part select told me because the Icemaker Bearing and Cup Assembly was larger than the original one. Thus, I had to switch it with the old one really quick so instead of a 3 min job it was 20 or so.....

SOOO EASY TO REPLACE

  • Customer: Heidi from Novato CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
This was a very simple piece of kit to replace. We are not electricians but commonsense helped. Follow the man's advice below me but you don't need to empty the whole refridgerator just the top shelf. Very, very simple. Thank you the man below.

Ice maker motor would run continuously but the blades would not turn and no ice came out.

  • Customer: Gary from Medway MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
I wasn't sure what the problem was, but the ice maker seemed simple and on-line resources suggested the control and motor assemblty was at fault. I searched the internet and Partsource had great diagrams which I could match to the part in hand. The price was right (way less than the local stores) so I ordered it.
I unplugged the unit from the power in the freezer, but unplugging the entire refrigerator works too. I pried off the white cover on the front of the ice maker, which snaps in place top and bottom. There are three screws holding the contoller (the entire front piece), remove them, pull off the controller and push the new one in place. You may have to turn the blade shaft to line up the notch on the shaft to the motor. Then reinstall the three screws, The screws go into plastic so it is easy to cross thread them, so be careful, I actually think I did with no ill effects. Snap on the cover and repower the unit. Done. Simple and quick.

I broke the old cap trying to turn the filter cc wise.

  • Customer: Victor from San Mateo CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 12 people found this instruction helpful
I installed the new cap on a new filter, which I will install when the old filter needs replacing. No tools required, but it is sometimes difficult to turn the filter cc wise, when replacing.

WOULD NOT MAKE ICE.

  • Customer: Zach from Danville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 9 people found this instruction helpful
AFTER LOTS OF INTERNET EXPLORING AND DIAGNOSIS, THE ICEMAKER COMES RIGHT OUT, AND WITH THREE SCREWS OUT AND IN, THE JOB IS ALL BUT DONE. DON'T PAY ANYONE FOR THIS REPAIR!!!!!

broker door on ice shute

  • Customer: John from Willington DE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 21 people found this instruction helpful
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.

Ice Maker stripper arm cracked

  • Customer: Mark from Newtown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Ice maker was flooding freezer

  • Customer: Raymond from Zwolle LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench set
  • 7 of 9 people found this instruction helpful
Replaced 8 cube ice maker assembly. Contrary to instructions I 1st removed 2 screws on the flapper door 2 removed 3 screws in bottom and 1 screw on right side bottom and pulled shelf out unplugged plug and lifted assembly off put new one on shelf plugged it in and slid it back into place replaceing. screws. was done in 10 min. start to finish . so far seems to have solved the problem.

The Icee ejector arm stopped turning due to icecube jam.

  • Customer: Leonard from South Euclid OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!

plastic ice cube guide installed

  • Customer: Richard from Bloomington IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then received it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.

Diffuser started clicking and would not regulate the cold air from the freezer section into the coldbox section. Vegtables kept freezing.

  • Customer: JAMES from CARDIFF CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
One screw inside the refrigerator removed the cover exposing the diffuser assembly. I had to also remove the cover inside the freezer compartment in order to free the diffuser assemble bracket that protruded in from the refrigerator compartment directly on the other side. Once the diffuser was freed, the assembly came off in my hand. The new one just snapped back in place. Done.

Ice maker leaked into ice reservoir

  • Customer: joe from hilliard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
The ice mold has a coating on it. Over time the coating deteriorates. If your ice maker leaks water into the ice reservoir inspect the mold to see if the coating is compromised. If so, replace with new.

Remove the ice maker assembly. 3 small hex screws. Unplug power cord. Disassemble ice maker assembly. Remove ice mold/heater. Replace with new. Reassemble.
All Instructions for the 10644102300
61-75 of 759