Models > 10644039601 > Instructions

10644039601 Kenmore Refrigerator - Instructions

All installation instructions for 10644039601 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644039601
61-75 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ref Side Not Cooling Properly& Noisy

  • Customer: DAVID from GRANBURY, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 18 people found this instruction helpful
Looked at repair diagram, ordered part [ fast shipping ],first empty freezer pulled everything out removed rear panel, removed motor, installed new motor into housing. Using a heat gun [on low ] defrosted ice build-up on coils, this tookover one hour , reinstalled everything and it started right up but took 24 hours to stablize and get the ref / freezer back to the -10/37 degree . All better and quiet now. Last time I paid for the repair over $200 very happy thank you part select

Ice maker quit making ice.

  • Customer: Kearney from Port Allen, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 18 people found this instruction helpful
Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.

Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.

  • Customer: George from Cottage Grove, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 15 people found this instruction helpful
I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

It was just time to replace the water filter.

  • Customer: Denise from Hoschton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 22 people found this instruction helpful
We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

Ice maker broke and not repariable

  • Customer: Colleen from Chesapeake, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
PartSelect was fantastic and I would recommend them to anyone! Online, Sears only showed a parts breakdown so I went to the service center. They could sell me an ice maker but PartSelect had the same ice maker for $35 less and it was on my door step the very next day! Mu husband plugged it in an we were on our way. You have been very easy to work with. I was amazed at the delivery time and I will use you in the future!

Ice door holder arm broken

  • Customer: Joseph S from Las Vegas, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 19 people found this instruction helpful
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

ice distribution door broke

  • Customer: David from Winston-Salem, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 13 of 17 people found this instruction helpful
At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

Motor was noisy

  • Customer: Rick from Florence, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 12 people found this instruction helpful
I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Refrigeator would not drfrost...

  • Customer: Curtis from Pikeville, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 17 of 30 people found this instruction helpful
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Ice dispenser freezing up, dispenser door not closing completely.

  • Customer: Robert from Valencia, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 15 people found this instruction helpful
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

Ice Maker stripper arm cracked

  • Customer: Mark from Newtown, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 13 people found this instruction helpful
This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Ice stuck in mold. mold coating was peeling off.

  • Customer: Martin from Shakopee, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 13 people found this instruction helpful
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Cover Pan Crisper(bottom glass shelf and frame) were broken

  • Customer: anthony from ormond beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
New part slipped right into the studs and fit perfectly

coupling on water line thru freezer door cut due to moving Refg and having to remove doors.

  • Customer: Martin from Rutherfordton, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 31 people found this instruction helpful
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.

Dead condenser fan/motor

  • Customer: Drew from mountville, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 11 of 14 people found this instruction helpful
Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.
All Instructions for the 10644039601
61-75 of 651