10644032600 Kenmore Refrigerator - Instructions

replace the emitter and receiver which is located on the left and right side of your freezer when you open the door. use a crosstip head screwdriver remove the 3 ea. screws on the emitter frame ,dothe same for the receiver. replace the electronic boards and reinstall.wait at least 30 minutes and listen for ice to drop in the ice bucket.

Watched the trouble shooting & installation videos , checked to make sure water was getting to the door. I look'ed closely at the entire unit. Every thing seem'ed to be ok. I made a guess as to which part to order. The control motor or the thermostat. The control motor made more sense to me. I made the right guess. Works like new.

I couldn't figure out if the front plate would come off so getting access to the screw to unscrew it was problematic at first. I don't have whatever tool you need to get at that angle so I used an Allen wrench with a 6.5 mm socket to unscrew the screw and replace the clip. After figuring that combination out it went really fast.

Parts Select has great videos that describe step-by-step how to perform the repair. I did a sloppy job of diagnosing the problem, and concluded it was the water valve. The actual problems was that the ice maker was not sending a signal to the valve to send water. I could have determined this if I had tested the ice maker using all of the connection points where a jumper wire could be inserted. The ice maker arrived on my doorstep exactly when promised, and was an easy ten-minute fix. My conclusion is that an average person CAN work on their own appliances with a company like PartsSelect to backstop them.

Watched video, used putty knife to remove front panel, unplugged wired and then took old arm off, and replaced it with a new one. Also disconnected electricity before repair. Thanks for the tips, fast shipping, and helpful video.

Installed two circuit boards which was very easy & within 30 minutes ice was being made

I watched the film on installing and taking out. Step by step. easy.

My name is Tuan Nguyen. I have no ice and no water dispense into icemaker tray. I replace the the icemaker control and motor assembly. I unscrew a screw underneath the icemaker unit and disconnect the wire clip and pull out the icemaker assembly. I remover 3 screw from the motor assembly unit and replaced it with the new motor assembly. and installed the unit back in the compartment. It took about twenty min. It make me look good, that my wife knows i can fixed the problem without calling the repair men.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

The comments from PartSelect were 50/50 that it would be the motor on the icemaker. We bought the motor which came 4 days leter and followed the installation instructions in the video. We started getting ice about 2 hours after the installation!

Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

Replaced the Electronic control boards first, emitter and receiver, and that did not fix the problem. I then order the Control board/motor assembly in the ice maker, this did fix the problem and after a couple of hours I had ice. The repair was easy and the videos on the web site show you step by step.

Thanks to this site, it told me what was wrong, what to order and how to repair it.