Models > 10644024600 > Instructions

10644024600 Kenmore Refrigerator - Instructions

All installation instructions for 10644024600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644024600
931-945 of 983
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker stopped making ice

  • Customer: stephen from chico CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.

Ice Maker not working

  • Customer: Thomas from PALMYRA VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There were excellent entries on the net of how to diagnose problem. Parts Select website had an excellent video on how to change part. Just followed instructions and changed parts in about 15 minutes. I am usually a klutz, but this was so easy

Ice Maker had stopped making ice

  • Customer: Connie from Mt. Vernon KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.

Ice Maker Did Not Make Ice

  • Customer: Rodney from Sacramento CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed a total of 12 screws, unplugged the control boards, plugged-in the new control boards and replaced the 12 screws.The FAQs section of the PartSelect troubleshooting guide helped me correctly identify the control boards as the source of the problem. The LED sequence was the key to identifying the problem.

No ice after replacing the ice controller...

  • Customer: Greg from Escalon CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

ice maker not sending ice down chute

  • Customer: CLAYTON from KISSIMMEE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and realized how easy it really was....followed directions and completed repair in less than 5 min....only issue Fed Ex lost original order....parts person was great...overnighted me a replacement

Ice maker would only make ice intermittantly

  • Customer: Thomas from Chambersburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I started by viewing the video online showing how to make the repair. I then unplugged the fridge, taped the cover of the icemaker up out of the way. It was then a matter of removing three screws on both the emitter and receiver sides of the freezer and two screws each to remove the boards. I uplugged the modular plugs from each board and then reversed the proceedure. Icemaker is now working like new.

Filter cap had broken

  • Customer: Bottom Line from Marietta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just press the new replacement cap over the end of the water filter.

Not making ice

  • Customer: Marshall from Poteau OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video about how to repair the ice maker and saw that it was super easy. I ordered the part and it only took two days to come in. Installation was super easy to do. The hardest part was getting the wiring harness to lay back so every thing would slide in. It took about 30 minutes total to get the old one out and the new one in. The video helped greatly. It started making ice within 10 minutes of turning it back on. I'll order from you again when I need parts.

Ice maker stopped working

  • Customer: Elmo from Palm Coast FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
April 2012
My ice maker (2001 Whirlpool Gold side by side) stopped making ice. Using the model number (inside fridge, right wall), Google found the partselect website containing diagrams of the entire refrigerator. Using the "freezer liner" and "ice maker" diagrams, I discovered that electronic control boards, control and motor assembly, and water inlet valves could cause the ice maker to stop making ice. Since the LED lamps in the freezer liner were not working (diagnosis described as part of the emitter control board description), I replaced the emitter control boards first. After installation, the lights worked properly, according to the diagnosis, but still no ice. It seemed logical to next replace the control and motor assembly. About two hours after installation, the ice maker produced cubes, and has been working since. Each of the two parts orders from PartSupply came within 3 days, and were the correct parts for my machine. Installation illustrations were accurate and helpful

Ice maker not working

  • Customer: Gary from Plymouth MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part recommended by your site, followed the instructions of the associated video and new ice is piling up right now. My only concern was no action for a time right after the install. Turns out the temperature of the freezer must drop back down to ?? before the ice maker starts to work. I was thinking maybe the electrical connection was not good. I choose to wait a night and see if change would occur. Freezer cooled down and ice maker started.

Gary

Refrigerator Door wont close

  • Customer: Peter from Saratoga Springs NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Removed the door, removed the old lower door cam, and replaced with new cam.

stopped producing ice

  • Customer: Walter from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

Ice Maker stopped making Ice.

  • Customer: Charles from Fredericksburg VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Opened freezer section of refergerator and taped Ice Maker cover door in the open position to remove emitter and receiver boards. Unscrewed the phillips head screws that secure the emitter board housing to the refrigerator side wall. Turned off power to the refrigerator and unpluged the emitter, removed the 2 screws that hold the emitter board against the housing and removed it, then I installed the new emitter board in the housing by screwing it in place. Repeated same process for removal and replacement of the receiver board. The whole process took me about 10 minuets.

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.
All Instructions for the 10644024600
931-945 of 983