Models > 10644024600 > Instructions

10644024600 Kenmore Refrigerator - Instructions

All installation instructions for 10644024600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644024600
886-900 of 983
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker Did not make ice

  • Customer: Julius from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply followed the step by step instructions demonstrated in the online videos for replacing the electronic control boards - emitter and receiver. Just that simple. 15 minutes later the repairs were completed. We've had ice ever since.

ice maker stopped harvesting ice

  • Customer: Scott from Lake George NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked the trouble shooting guide with the refrigerator and all signs pointed to the Electronic control boards that sense when the ice tray is full. After reading what other customer posted on this site I ordered the parts. I received the parts in two days time and had a harvest of ice within minutes of installing it. Thanks PartSelect. Scott

broke when intalling ice unit

  • Customer: bobbi from chehalis WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
repair was not to bad. removed 3 screws, then unplug wire harness. The next thing i did was removed clip that holds pin. slid pin back enough to put new flipper in place. needs to go in front of spring.once in place slid pin back in and put clip holder back on. Then plug wire harness back in and 3 srews . done.

Ice door got freezed

  • Customer: Nivia from Miami FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
With the flat screwdrivers, table knife or something to pull the front cover, is not easy but it will come out, patient and kepp trying until you made it, the rest is easy.

Ice make did not make ice

  • Customer: Susan from Collegeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the old ice maker. disassembled the part to reattach the housing to my new part. Hooked up the wiring and reinstalled the part. VERY EASY!!!!Our repair man had quoted me a price over $500. I was all done for under $150 including a new drip guard!

Replacing Icemaker in side-by-side refrigerator

  • Customer: Lawrence from Silver Spring MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
About a year ago, my icemaker stopped making ice. Knowing that a "house call" would cost a fortune, I delayed calling for a repair. Then I discovered the instructional videos on this (and other) websites. Looked like a relatively easy job. Troubleshooting the problem, however, had me scratching my head. Was it the control unit? the ice maker? the water pump? a frozen water line? A 4 day power outage allowed me to rule out the frozen line. The forum here allowed me to rule out the control unit (the blink codes indicated that it was working). So, the pump or the icemaker? Hmmm. I poured some water into the icemaker to see if it would make ice (I think that was a hint on the forum). No ice, so I ordered a new icemaker (and it arrived very quickly). It was very easy to take the old maker out. Some very minor complications with the new icemaker. First, the "funnel" for the water into the icemaker was a bit taller than the old one so had to manuever the water tube into the "funnel". The second problem is that the electrical connector on the icemaker seemed to be longer than the old one so the connector extended beyond the white cover. Not really a problem but it made it difficult to fix the cover over the wire. In the end, it just left it fitted loosely, without screwing it in place. All in all, however, a very straight forward undertaking (made even more so by the excellent videos)

The Ice Cube maker tray would not refill with water

  • Customer: Charles from Broadview Heights OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
PS328747 Icemaker and Water Dispenser Dual Inlet Valve was purchased from Parts Select. My wife, Sandy, watched install video provided by Parts Select on their website. Sandy used plywood to protect our hard wood floor. She pulled out the refrigerator (She did need my help to do this task). Unplugged the refrigerator. I turned off water line in the basement. Sandy followed the video to the tee. Fifteen minutes later the part was installed. The ice maker tray was quickly filled with water. Ice cubes quickly were made. My wife is uniquely talented. Last winter, she remodeled two bathrooms in our Naples home replacing all the fixtures, vanities, flooring, etc. My wife can do almost any task. Many years ago, I had a leaking radiator and a broken arm at the same time. What did she do--she removed the radiator from the car, took it the repair, and reinstalled the repaired radiator. Sandy plays tennis, golf, brige, hikes, sings in the church choir, works at theater as a red coat, and at 62 years of age, she tackled another item on her bucket list in January 2012. Sandy's first recital is Saturday--she is quiet an accomplished pianist already. I could relate many other stories about her but the most important one is that this beautiful woman has been wife for 43 years and the mother of our two beautiful daughters, Jessica and Holly.

Broken drawer

  • Customer: Debbie from Westland MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced old drawer with new. Did have to remove white handle, the new one doesn't come with one. It was simply a matter of prying up the edge until it would come off and snapping it in place on the new one. Used the screw driver to lift pry up the edge.

ice maker stopped producing ice

  • Customer: Dennis from Lake Almanor CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
very simply followed installation instruction...removed 5 screws, disconneted electrical plug-in, installed new ice maker.

light switch sticking

  • Customer: Paula from Rush NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

Light did not come on (bad bulb!) on TC18KL

  • Customer: Louis from Beloit WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

rocker switch broke off

  • Customer: STANLEY from OAKLAND NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Light switch which turns on the lights when the door opens went out

  • Customer: Dennis from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Light in my refrigerator didn't work.

  • Customer: Joseph from Byron Center MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

exchange of defective light rocker switch

  • Customer: Steve from River Edge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
All Instructions for the 10644024600
886-900 of 983