Models > 10644023602 > Instructions

10644023602 Kenmore Refrigerator - Instructions

All installation instructions for 10644023602 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644023602
871-885 of 915
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker stopped making ice

  • Customer: Ronald from Hebron KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
research of company website showed parts to buy (per percentage of failure) and how to install those parts I viewed video on installation of parts and did the job, it was a snap

icemaker inop would not harvest

  • Customer: howard from bruceton mills WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
easy,remove old parts installed new parts,icemaker started working properly.

Ice maker was not making ice

  • Customer: William from princeton WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used the video on your web site. also read the overview made things really simple

In the Door Ice Maker stopped working

  • Customer: Ed from Germantown OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

Both light bulbs had been replaced, but lights did not turn on.

  • Customer: Richard from Arlington MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Ice maker stopped working

  • Customer: Steve from weatherford TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
No prior experience in appliance repair. The majority of time was used in researching the problem and how to fix it. The Parts-Select website and the comments of prior customers made it easy to diagnose and repair. Unplugged the unit, popped of the ice maker cover to get it out of the way, unscrewed the plate covers for the emitter and receiver, changed them out, replaced the covers, replaced ice maker cover, plugged in. Moved on to the next problem.

stoped making ice,red light blinked twice,did test,found out control boards bad

  • Customer: Brian from Santa Clara CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched video and did same thing,works great now,ordered parts friday morning arived saturday,very pleased!

replaced icemaker

  • Customer: Ronald from Kissimmee FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
good repair no problem.

ice maker wasn't

  • Customer: Mona from The Sea Ranch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

Ice Door not closing properly

  • Customer: Jennifer from Sahuarita AZ
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I did the repair, but apparently there's an Ice Door Kit with Bracket ( Part #8201756 - PartSelect Number PS990120 ) that has a metal bracket that will actually fix the problem with the broken plastic that holds the pin in.

Broke the arm off the food compartment rocker switch

  • Customer: David from St. Pete Beach FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Unit stopped making Ice

  • Customer: Denis from Columbia IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

timer motor died

  • Customer: Paul from Moline IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

Ice door assembly broken, freezing up ice maker

  • Customer: Sandra from Burlington NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

indtalled new part WPL W10190935 and it did not fix problem

  • Customer: Ronald from Jeffersonville IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
as shown in instructions
All Instructions for the 10644023602
871-885 of 915