Models > 10644023601 > Instructions

10644023601 Kenmore Refrigerator - Instructions

All installation instructions for 10644023601 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644023601
556-566 of 566
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker Not Making Ice

  • Customer: Gail E. from Palm Harbor FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The part arrived very quickly. I set up the laptop computer on the counter and started the instruction video (THEY ARE THE BEST!). With just a few starts and stops of the video during the installation in less than 15 minutes the repair was complete! The next day I had more ice than I needed. What a fabulous way to make appliance repairs at minimal cost! I will ALWAYS use PartSelect for any future repairs. I should also tell you that a 70 year old Woman did this repair - easily! If I can do it so can you!!

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

No Ice

  • Customer: James M from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Ice maker unit

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

condenser fan motor making alot of noise, possibly going out.

  • Customer: rex from folsom CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

NO ICE- DRIVE GEAR ON ICE MAKES BROKEN OFF

  • Customer: TOM from ZANESVILLE OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
THE VIDEO ON YOUR WEB SITE IS GREAT!! I HAD REMOVED OLD ICE MAKER AND FOUND THAT THE MAIN DRIVE GEAR WAS BROKEN OFF. REC'D NEW ONE IN 2 DAYS REMOVE BOTTOM COVER TO PUT ON NEW ICE MAKER REINSTALL. THANKS FOR THE HELP AND GREAT SERVICE!!! TOM

Compressor fan and motor was load,barring was wobbling .

  • Customer: William from Fox lake IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Fast after a little help from a friend

Ice maker would not send ice through the dispenser

  • Customer: jonathan from austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Opened the freezer door. Removed the ice bin from the freezer compartment. Removed with a nutdriver the two screws holding down the shaft holder (the triangular white plastic piece). Removed the shaft holder and the circular seal underneath. Pulled the hexagonal metal shaft up and out of the dispenser motor. Installed new circular seal and reinstalled the plastic shaft holder, etc..

Ice maker broken.

  • Customer: Ken from Boise ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered the ice maker assembly..received it within 4 Days of ordering it.It took less than 15 minutes to install.Removed the screw that holds the wiring cover.pulled the old ice maker out.unhooked the wiring harness from the old one.unscrewed the bracket from the old ice maker installed it on the new one.Plugged the new ice maker in slid it in put the wire cover back on.It was making ice within 30 minutes. Thanks partselect.

I accidentally broke the arm that distributes the cubes to the ice bucket about a year ago. Just recently, the malfunction caused the entire thing to freeze up because the frozen cubes weren't cleared from the ice tray.

  • Customer: Timothy from Brunswick OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove 1 screw from the cover that hides the wiring harness, pull out the assembly and disconnect it. Swap the bottom mounting tray to the new ice maker and reverse the process. Way easier than I anticipated. No need to freeze your hands in the freezer, once you have the old one out you're working on the counter.

exchange of defective light rocker switch

  • Customer: Steve from River Edge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
All Instructions for the 10644023601
556-566 of 566