Models > 10644023600 > Instructions

10644023600 Kenmore Refrigerator - Instructions

All installation instructions for 10644023600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644023600
736-750 of 931
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker just quit working!

  • Customer: Keith from Sanford ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

Ice maker stopped turning out ice

  • Customer: James from Wasilla AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed three screws. Removed old part. Inserted new part and reinstalled three screws. Doesn't get much easier that

icemaker does not make ice...mech cycles normally

  • Customer: Don from Lanham MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

My ice maker quit working

  • Customer: pauline from somerville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have some electronics background but your listed problems helped me narrow down the problem. I ordered the part, removed old part, installed new part (maybe 15 minutes total) and my icemaker started dumping the ice that was in the tray within 20 minutes and making more. That clunking sound of ice was music to me ears and wallet!! Thanks!!

Ice maker wasn't getting water

  • Customer: Anna from Morgan Hill CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called a repair man out to see what the problem was because my husband just died and I didn't want to pay such high prices for a repair. He told me I needed a new motor for the ice maker and it would be a total of about 305.00. I couldn't believe the price. It cost me 59.99 for his diagnosis. I went to your web site and found the part and watched you installation video. I am 65 years old and I was able to install the new part in less than 15 min. The part was about 95.00. I saved 150.00 by doing it myself. I will always look on line before I have a repair man do a job. I may need them to diagnose the problem, but I will try myself before paying such outrageous fees.

Ice Maker stopped making ice.

  • Customer: Lucy B from Beckley WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I called a repairman, who removed the ice maker and reinstalled it, not once -but- three different times and charged me $84.60. (That's all he did.) I remembered, PartSelect, watched video, ordered motor, received in three days, installed in less than fifteen minutes. Within ten minuted water was running in and later ice was dropping into bin, next day bin was full. Wish I had trusted myself and looked up my fridge problem on PartSelect before calling that (repair) man, and saved myself $84.60. By the way, I'm a 67 year old female.

Ice maker was not making ice.

  • Customer: Carl from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I'm sorry I can't help you with this, as one of my sons diagnosed the problem and did the repair for me. It took him maybe five minutes to swap the parts, and the ice maker has been working fine ever since.

No ice

  • Customer: James from Thorp WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
When very smoothly, as the video outlined the procedure.

Ice maker would not make ice.

  • Customer: Robert from Rockville MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on the PartSelect videos I found on YouTube. (turn off ice maker) 1. remove cover by GENTLY pushing pins aside, 2. remove screw underneath right/rear, 3. remove plastic thingy that the screw went through, 4. push up tabs underneath left & right, 5. slide out ice maker, 6. disconnect wiring harness, 7. pull off plastic cover (no screws), 8. remove 3 screws from controller, 9. install new controller, then reverse 1. thru 8. Unfortunately I was a little heavy handed when removing the cover and broke the bracket. I replaced it at the same time for about $10 (off & on with 2 screws).

fridge stopped making ice

  • Customer: Chris from Bethel Park PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed cover took out 2 screws put in new unit put 2 screws back in put cover on done

ice maker did not work

  • Customer: Arnold from Renton WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video indicated the removal of the entire ice maker when replacing the motor unit that I had ordered. Since I was replacing only the motor unit, located immediately to the front of the ice maker, made visible after removing the snap on cover, I chose not to remove the total unit and removed the old motor unit with the new one ordered and was successful with no further problems. I did turn the water off and disconnected the electrical plug of the fridge first. Three screws removed and replaced and done.

my ice machine stopped working

  • Customer: Jason from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My ice machine stopped making ice I noticed the little dial under the cover stopped turning, so I bought the replacement part. It arrived three days later I un screwed the old one, and put the new in place and screwed it on the only little thing you might need to know is that the metal lever arm that moves up and down is attached to a plastic grommet with a two prong release that protrudes through the hole on the front of the assembly to release the old one just pinch them together. My ice machine works great now it was a very easy part to replace no need to call a repair service anyone with a screwdriver can replace this part

No Problems!

  • Customer: vernon from fairfield CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
FOllowed the vedio instructions which made the installation very helpfull.

Icemaker stopped working

  • Customer: Gloria from Woodstock Valley CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First, I went online and looked up the directions to remove the ice maker. After several attempts of removing and re-installing it, I found that one of the tines on the wheel had broken of making it impossible for the ice to dispense. I went online to PartSelect, found the exact part I needed, not the new replacement one either, and watched the proper installation directions on the website. When the part came, I did exactly what the video said, which took me maybe 10 minutes, and plugged the fridge back in - make sure you unplug the refrigerator - don't just shut it off!! I heard the water going into the maker, and about 30 minutes later I heard the first batch of ice fall into the bucket!!! It was music to my ears!!!! Oh, and by ordering from PartSelect and doing this simple repair myself, I saved $150.00!! PartSelect is now my new best friend!!!

Would not make ice.

  • Customer: Crystal from Mountain Home AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove icemaker, take off Icemaker control & motor ( 3 screws ) & install new part. Started making ice in less than 24 hours. Very happy customer.
All Instructions for the 10644023600
736-750 of 931