Models > 10644022603 > Instructions

10644022603 Kenmore Refrigerator - Instructions

All installation instructions for 10644022603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644022603
46-60 of 566
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

BROKEN SHELF BRACKET

  • Customer: Thomas from Leesburg FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 14 people found this instruction helpful
REMOVED FOOD ITMES ON BROKEN SHELF. REMOVED OLD GLASS SHELF COVER. REMOVED BROKEN SHELF BRACKET. INSTALLED NEW SHELF BRACKET. INTALLED NEW GLASS SHELF COVER. REPLACED FOOD ITEMS BACK ON SHELF

Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.

  • Customer: George from Cottage Grove MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 12 people found this instruction helpful
I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

Refrigeator would not drfrost...

  • Customer: Curtis from Pikeville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 13 of 22 people found this instruction helpful
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Ice stuck in mold. mold coating was peeling off.

  • Customer: Martin from Shakopee MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 10 people found this instruction helpful
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Motor was noisy

  • Customer: Rick from Florence SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 10 people found this instruction helpful
I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Ice door holder arm broken

  • Customer: Joseph S from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 11 people found this instruction helpful
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Water dispenser hose tip broken.

  • Customer: Sean from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 14 people found this instruction helpful
The part to fix this was a $50.00 part.
I purchased this Bracket Dispenser for $6.00 and it fit on My fridge perfectly. I just used the screw hole that was a little higher on the water dispenser. Simply cut off the broken end / or Buy a new Hose (Cost at Lowes about $6.00) guide hose along the bracket and use a socken set to reinstall the screw. Water is not squirting on people any more.

Icemaker works inytermittantly.

  • Customer: James from Walnut Grove MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 11 people found this instruction helpful
I removed cleaned & re-ionstalled the same unit. It started to slowly make ice and then stopped. I repeated the above procedure again and it started to work normally. I will keep the replacement icemaker as a handy spare. I fear it will fail again in the near future.

Refrigerator indicated that water filter needed replacement

  • Customer: Roy from The Villages FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 17 people found this instruction helpful
It took less than 5 minutes to remove the old filter and install the new one. Push a button and the old one pops out, stick in the new one, and you're done.

Ice dispenser freezing up, dispenser door not closing completely.

  • Customer: Robert from Valencia CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 8 people found this instruction helpful
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

Ice maker quit making ice.

  • Customer: Kearney from Port Allen LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.

Not Making ice

  • Customer: Neil from Berlin MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 9 people found this instruction helpful
I took a 1/4 nut driver and removed the wire cover. I then used a small screwdriver to push up the clips the lock the unit in place. I then unplugged the unit and removed. I then used the same nut driver and removed the bottom plastic cover and installed it on the new icemaker. I then put the new unit part way back onto it slides, being carful to make sure the water fill spout clears the unit. Next I plugged in the wire harness and then slid the unit the rest of the way in until it locked in place. I then reinstalled the wire cover.
This unit was delivered at 1:30 and it was installed by 2

ice maker not working

  • Customer: mike from citrus heights CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

ice distribution door broke

  • Customer: David from Winston-Salem NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

Old motor was not resetting back to proper position halting ice production.

  • Customer: Kevin from Spring TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 7 people found this instruction helpful
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
All Instructions for the 10644022603
46-60 of 566