Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644022601 > Instructions

10644022601 Kenmore Refrigerator - Instructions

All installation instructions for 10644022601 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644022601
556-570 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water dispensor leaking/Retainer clip bent

  • Customer: glen from Rancho Cucamonga, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I couldn't figure out if the front plate would come off so getting access to the screw to unscrew it was problematic at first. I don't have whatever tool you need to get at that angle so I used an Allen wrench with a 6.5 mm socket to unscrew the screw and replace the clip. After figuring that combination out it went really fast.

No ice from ice maker

  • Customer: William from Moscow, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Parts Select has great videos that describe step-by-step how to perform the repair. I did a sloppy job of diagnosing the problem, and concluded it was the water valve. The actual problems was that the ice maker was not sending a signal to the valve to send water. I could have determined this if I had tested the ice maker using all of the connection points where a jumper wire could be inserted. The ice maker arrived on my doorstep exactly when promised, and was an easy ten-minute fix. My conclusion is that an average person CAN work on their own appliances with a company like PartsSelect to backstop them.

Water dispenser was broken off

  • Customer: Judy from Palmyra, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Watched video, used putty knife to remove front panel, unplugged wired and then took old arm off, and replaced it with a new one. Also disconnected electricity before repair. Thanks for the tips, fast shipping, and helpful video.

Ice maker would not make ice

  • Customer: Steven from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed two circuit boards which was very easy & within 30 minutes ice was being made

fan motor

  • Customer: James from Kennett, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I watched the film on installing and taking out. Step by step. easy.

Ice maker quit making ice

  • Customer: david from Surprise, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the reviews on how to test if part was bad. It was! Ordered new infered sensors and watched your repair video! 2 hours later the ice maker was making ice:) Very easy! Thanks David

The icemaker stopped working

  • Customer: Patrick from gilroy, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker and installed the new one. Went from six tiny ice cubes to four big ice cubes. Ice is of a higher quality, and the ice no longer falls out of the bin as the old ice maker's ice had once been prone to doing. A certified epic win on my part.

Water leaking and freezing on the botton of the icemaker mold

  • Customer: Richard from Jacksonville, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Install was done in reverse order of uninstall. The only thing that made this install a bit tricky is that the fill cup on the replacement icemaker was not the same part as on the original. I could have attempted to trim the replacement fill cup but didn't know how well that would work. I instead elected to install the original fill cup onto the new icemaker. This added a bit of time and complexity to the repair but I followed a repair video for when just the ice mold is being replaced. That video told me how to disassemble the ice mold and timer motor which had to be done to in order to replace the fill cup. It's been about 2 weeks since repair was made and the icemaker seems to be working properly.

Ice maker would not make ice

  • Customer: celene from Lavonia, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Completely disconnected the power. Just shutting off the ice maker switch does not shut off the power to these boards. The emitter and Receiver boards are located in the side panels of the freezer-one on the right and the other on the left. Just remove the 3 screws in each cover and disconnect the wire connectors and install the new boards. It's very straight forward and easy to do.

No ice, the cabinet was warm, but most annoying it broke every 6 mos since I got it

  • Customer: Cynthia from Wilmington, DE
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

Failed to make ice

  • Customer: Billy from Horseshoe Bay, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

Replace ice maker

  • Customer: Alfred from Jackson, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Remove the door on the icemaker. Remove a screw on the bottom right of the icemaker and remove the bracket. push two small tabs on the bottom to release icemaker and slide out. unclip plugs that are on the wire. To reinstall just do the reverse.

Ice mold was leaking causing all the ice to freeze into one chunk.

  • Customer: Douglas from Spring, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

condenser fan would not come on, and when it did, made loud noise.

  • Customer: Sean from Simi valley, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Water would come through the door, but would not make any ice

  • Customer: Chad from Marrero, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the (3) screws on the bottom of the ice maker & the (1) screw on the electrical cover plate. I unplugged the ice maker & completely removed it from the freezer. Make sure to pay attention to the locking tabs or your maker will not come out. I took the bottom plate off the old ice maker & attached it to the new one, slid it in & re-plugged it. Tighten all screws back where they are to go & now I have ice. It was a breeze to do this job. Part was completely as described.
All Instructions for the 10644022601
556-570 of 651