10642106301 Kenmore Freezer - Instructions

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

It was very easy. The part make look different online but it was a proper replacement.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

I have a Whirlpool side by side refrigerator/freezer, 12 years old. One day it just stopped cooling and there was water running under the fridge (melted the ice in the ice bucket). Checked the freezer fan and it was working. I also checked the condenser fan by checking air flow under the fridge; there was airflow, so it was working. Listened to the sound of refrigerator. Noticed the compressor was coming on and after a few seconds clicked (tripped). I figured either the compressor is burned or the Start Device is bad. Turned the plug off, took off the lower back cover using a nut driver. Removed the clip holding the Start Device and gently unplugged the Start Device from the compressor. Measured the resistance across compressor terminals. They should all read some resistance (10,6,4 ohm roughly). Also checked the continuity between each terminal and compressor shell. They were all open (means no shorting). I figured the Start Device should be bad. Ordered new part for $40, replaced it with old one, put the cover back on. Plugged the unit on and everything was working. Remember that it takes a while to cool both compartment, so do not expect the fridge/freezer to get cool quickly.

Definitely need to watch a youtube video on how to do it. No instructions come with the gasket so you need some instructions. Once I managed to get it started it went fairly quickly. Difficult to get it started but once it is started it is not too difficult

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

I just lifted up the door shelf and removed it. Threw it away and replaced it with the new one. It looks beautiful.

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!