Models > 10641569802 > Instructions

10641569802 Kenmore Refrigerator - Instructions

All installation instructions for 10641569802 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641569802
376-390 of 432
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator and freezer stopped cooling.

  • Customer: Jonathan from Puyallup WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Went to the site to determine the problem and ordered the three most probable causes to my situation. replaced two of the items and had to send one part back because it didn't exist on my Model. Still did not run. Went back to the site and ordered the thermostat and the problem is resolved.

The old drawer was broken from wear.

  • Customer: herbert from perkinston MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took it out and slipped the new one in.

crisper was broken

  • Customer: carolyn from sherman TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just remove the damaged one and replace with the new one---easy- breezy

The refigerator door would not close easily - stayed ajar unless pushed closed

  • Customer: Charles from Santa Barbara CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Great video on-line - remove door by unscrewing bracket (3 screws) at top of door; the door magnet will hold it to the face of the frig until you are ready to lift it off... Lift door off and position horizontally across a padded table or sawhorses. The door is actually very light in weight. The cams at the bottom were easy to put on - use care not to overtighten the retaining screw. The top thimble takes a lot of time to "dig out" of the top of the door - hard not to mar and bend the door in this area. This took almost one-half hour to get it out!! Putting in the new one, use care to not cave in the door corner, not a lot of structural strength in the area. Once all the door items are in place, put the door back in place on the frig and replace the top bracket to hold it in place; watch to line up the gap between the frig and freezer door so it hangs straight. Check the two cams at the door bottom - they won't fit perfectly when the door is in the closed position and that is OK... IMPORTANT - the door should now close, but it won't automatically shut on its own until you load the door back up with your food items. Once the items are in place on the door you will see that it now closes completely with very little to no effort... just like it should. Hope this is helpful!!!

Refridgerator would not run.

  • Customer: George from Wellsburg WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I Checked thermostat in freezer compartment for continuity I next checked defrost heater for proper ohms. both were ok. I assumed defrost control board could be only problem. changing control board located in upper right was simple ,pop off cover plate with small screwdriver remover four screws plug in new control board.

Drawer Damage (Cracked)

  • Customer: AKIHIRO from Maryville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just re-intall the new drawer. That's it. Thank you !!

Freezer OK. Refrigerator Not Cooling.

  • Customer: Donald from Kissimmee FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed recommendations from others but went with most likely by percentage = Defrost Timer Kit. Did not solve issue. Then went with Bi-Metal Thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part OK. Then I saw on line that I should have listened for Fan operation. I checked and found the fan Motor to be defective. Replaced the motor and Refrigerator worked fine. Both the Motor and Bi-Metal Thermostat were required. Should have checked fan operation first.

Cracked Crisper Drawer

  • Customer: Richard from Huntsville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the damaged unit and inserted the replacement.

Lower Door Closing Cams Worn down

  • Customer: Raul from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

fridge turned itself off, melting often

  • Customer: Irene from Margate FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I vacuumed the back and underneath, hoping it will solve the problem, but after about 2 weeks of hoping I succumbed.... finding the proper wrench was the most time consuming. After removing the screws, the face plate removal was the most challenging. You have to pry the top part carefully away (we used a knife), after it just drops down. Used a flat screw driver to loosen the wire harness, after that the rest was less than child's play. We are still in the testing mode, but so far so good. Freezer freezes, ice maker drops the ice cubes (not melting), fridge is humming. Wish us good luck.

Very Noisy

  • Customer: James from Fort Myers FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions provided on a video that was shown when I went to order the required parts. The video was very well done. It is very accurate.If you fololw the instructions you can make the repain in about 30 minutes. It was very easy

Refrigerator door was not closing "automatically", over time the plastic cams had worn out.

  • Customer: Mike from Egg Harbor Township NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

bottom door shelf bracket cracking

  • Customer: John from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unsnap old part and gently push new shelf bracket in till it snaps into place.

Heater not releasing ice

  • Customer: Terry from Bowling Green MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.

refrigerator and freezer would stay frozen.

  • Customer: Jack from Poplarville MS
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.
All Instructions for the 10641569802
376-390 of 432