10641564800 Kenmore Refrigerator - Instructions

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

very easy in about 2 minutes. snap the old out and slap the new in

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Ordered replacement parts from Parts Select on Sunday and the parts were delivered to my home on Wednesday . Could not be happier with this company. It was very easy to see exactly what I needed from the diagrams they provide on the website . Parts arrived and were installed in just a few minutes. I would, and have recommended Parts Select to my friends ... AWESOME !!

Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.

Remove rear panel with 1/4 nut driver. Pop plastic cover on compressor. Pry off relay and two wires and reinstall. Nice and easy and back to full function :)

Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

Been fighting this for over a year. Sometimes the fridge and freezer would heat up past the point it should come on. Had to slide the fridge temp control back and forth until the unit came on. Researched the problem determined the thermostat to be the issue. Got the part, finally found the time, then took the top tray out, popped off the escutcheon, unplug some wire and took out the control shuttle. Removed the old and replace with the new thermostat. Re-installed everything, plugged in it in and BAM. It's working. Now just fine tuning the slides to desired temps. THANKS PARTSELECT.