Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10641563801 > Instructions

10641563801 Kenmore Refrigerator - Instructions

All installation instructions for 10641563801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641563801
46-60 of 442
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not enough door storage

  • Customer: Dennis from Owings, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.

Crisper Pan Side Reales Had Cracked

  • Customer: LEVY from HOUSTON, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem

stopped cooling,the compressor would come on and shut back off.

  • Customer: william from shady dale, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the local appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.

installed ice maker

  • Customer: Dennis from Spring Valley, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 12 of 18 people found this instruction helpful
From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access

The freezer wouldn't freeze and the refrigerator wouldn't refrigerate.

  • Customer: Leandro from Baldwin Park, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

Cracked Crisper Drawer

  • Customer: Jennifer from Salvisa, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

'Frig door made a popping sound when opening and closing.

  • Customer: Lance from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

Rattling noise in beind freezer compartment

  • Customer: Herman from Cottonwood, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 14 people found this instruction helpful
remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

Broken tray

  • Customer: Brian from Los Angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
Remove old tray, replace with new tray.

Simple & easy.

Best part is I ordered on Monday & received on Tuesday!

The shelf runner broke

  • Customer: Andrew F from Media, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 15 people found this instruction helpful
Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.

light inside fridge was flickering and clicking

  • Customer: bill from escondido, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 12 people found this instruction helpful
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

The edges of the Meat pan slide were broken.

  • Customer: Michael from Bakersfield, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

Chrisper pan support cracked due to overfilling

  • Customer: David from Lenexa, KS
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 13 people found this instruction helpful
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.

burned out Evaporator Fan Motor

  • Customer: Robert from Surprise, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 14 people found this instruction helpful
simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

part broken

  • Customer: wilfredo from athens, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
i replace the old broken one, very simple and easy,thanks very much for the part, the price was really good better than sears, they were charging me for the same pretty much $100.oo, so thanks for everything, the time frame delivery was excelent!!!!! so i'll be keep you name first on my providers list for my next job......!!!!!!!
sincerely;
wilfredo Uztariz
All Instructions for the 10641563801
46-60 of 442