Models > 10641563800 > Instructions

10641563800 Kenmore Refrigerator - Instructions

All installation instructions for 10641563800 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641563800
406-420 of 445
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

my fridge did not have a cold cut and cheese drawer

  • Customer: Lynn from Lakewood CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The customer service people did some cross checking and found a shelf and drawer that would work in my fridge. It did!! I love it now!!!Thanks for your help I did have to remove one of the selves - but now I have an extra!

Broken Shelf for Door

  • Customer: Kelly from Waller TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slipped the shelf in the door

Crisper draw broke

  • Customer: thomas from garrison NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Package came in two days.I opened the box ,took the old draw out and slid the new draw in. Fixed in less than two minutes.I would definitely order from Parts Select again. Thanks for the prompt service

Clicking sound when opening door

  • Customer: mike from richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

My grand-daughter broke the crisper drawer by slamming the refrigerator door while the drawer was open.

  • Customer: Dotti from Vicksburg MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took out the old drawer and inserted the new drawer in the same place! I wish all of life were that easy!

Frig not cooling.

  • Customer: Adam from Randolph ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

Humidity Control Drawer broken

  • Customer: Juanita from Columbia SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Open fridge....empty old drawer....through out old stuff....remove broken drawer and take downstairs to trash bin. Remove new drawer from package....open fridge. Insert new drawer. Restock with remaining items. Have a cold drink and congratulate yourself for a job well done!!!

THE CRISPER DRAWER WAS BROKEN

  • Customer: Claudette from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
TOOK OUT THE BROKEN DRAWER AND REPLACED IT WITH THE NEW ONE. NO PROBLEM AT ALL.

The refridgerator door would not shut on its own. It had to be pushed completely shut every time it was opened.

  • Customer: Fred from Dacula AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.

exchange of defective light rocker switch

  • Customer: Steve from River Edge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

replace broken draw

  • Customer: SYLVESTER from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First, I took out the broken unit,yhen I put in the new one..

broken drawer slides

  • Customer: Michael from Marietta OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace drawe

Door wouldn't close fully, leaking cold air. light bulb went dead.

  • Customer: Mike from Sparks NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the door (3 bolts on top). Removed the old plastic door closing cam on the bottom. Installed the new one. It was too tall (probably my fault), so I trimmed it with garden shears (it was a tubular piece of plastic). If you do this, be very careful, as the shears cut through the plastic MUCH easier than I thought. Popped the new one on, re-secured the door, and it works great now. Thank you partselect!

Freezer side was freezing over.

  • Customer: Chris from Castleberry AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked at the parts diagram from partsselect.com and watched the short video. This was a huge help and made the installation of the new part actually easy. I removed the thermostat control panel from the top portion of the refrigerator side with a 1/4" nut driver and then removed the defrost control board with a philips head screwdriver. I then replaced the part and put everything back in place. The only problem I had was trying to get the thermostat control panel back onto the front clips.I would recommend partsselect.com to anyone. The refrigerator/freezer works great now. Thanks again. Chris

stopped chilling

  • Customer: Dave from Harrisville UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.
All Instructions for the 10641563800
406-420 of 445