10641562802 Kenmore Refrigerator - Instructions

I was amazed how easy it was to replace this control board. I printed the pictures and instructions for the part that were on your site. There was a video for another part and it allowed me to get familiar with the layout of my unit. Thank you very much.

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

very easy in about 2 minutes. snap the old out and slap the new in

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Ordered replacement parts from Parts Select on Sunday and the parts were delivered to my home on Wednesday . Could not be happier with this company. It was very easy to see exactly what I needed from the diagrams they provide on the website . Parts arrived and were installed in just a few minutes. I would, and have recommended Parts Select to my friends ... AWESOME !!

Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

Simply washed the part and installed

Took the broken one out and put the new one in. I am a very skilled craftsman. ;-)

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Pulled out the old one an put the new one in. I was impressed with how easy it was to work with partselect.com, I had alway ordered through Sears before, but from now on I will be using partselct.com for ordering parts. Got the part in two days with free shipping and $20 les than Sears that did not have the part in stock.

SUPER EASY!!!! I pulled the old one out and put the new one in. Perfect fit and it took less than 60 seconds. This web site was about $30 cheaper than ordering from Kenmore and it was identical. I ordered my Crisper Pan on Wednesday and got it Friday. Highly recommended!!!!!!!!!