Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10641522500 > Instructions

10641522500 Kenmore Refrigerator - Instructions

All installation instructions for 10641522500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641522500
1,006-1,020 of 1,126
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Installing Part for Ice Maker

  • Customer: Larry from Weeki Wachee, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Simply done !

Stopped making ice

  • Customer: BOB from HOCKLEY, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

Ice maker would not harvest ice (ice still frozen in ice maker)

  • Customer: Leonard from Hot Springs Village, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed ice maker from mounting rack but left wiring connected. Checked power between N & L: 120V (OK). Shorted T & H: no harvest cycle. Shorted L & V: no water came out to fill tray. Shorted H & N: heater did not turn on. Also noted that LED on right Electronic Control Board would flash 2X, then pause, then 2X, then pause, regardless of flapper position on left Control Board. Replaced Icemaker Control Assembly first (also purchased replacement Control Boards). Icemaker started working. Noticed that original Control Boards still worked the same way (LED flashing regardless of flapper position) BUT ONLY IN CERTAIN STAGE OF CONTROL BOARD CYCLE. At other times in cycle, LED would turn steady on when flapper closed, and right after tray fills with new water, LED does not light at all. Apparently this is NORMAL. I ended up not replacing old Electronic Control Boards. Icemaker took 3 days to totally refill ice bin - I presume this is also normal.

Ice maker stopped making ice

  • Customer: Richard from Stephens City, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

small plastic part in the icemaker control assembly broke, disabling entire system

  • Customer: Linda from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Ice maker would not make ice

  • Customer: Daniel from Central, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

icemaker stopped working

  • Customer: Patricia from Urbandale, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

Ice Maker would not eject ice from the ice tray.

  • Customer: Todd from Meridian, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

No ice

  • Customer: Janis from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Ice Maker stopped cycling

  • Customer: Milt from Littleton, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Did troubleshooting as manuel indicated. Had same problem once before. The replacement did the trick.

Wasn't making ice

  • Customer: Allan from Pasadena, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

no ice

  • Customer: john from centerburg, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
installed ice maker control & motor assembly

Ice maker not producing ice

  • Customer: Donald from Port ST Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installed the part suggested and within the hour it was making ice

Ice maker stopped making ice.

  • Customer: Russell from Sedro Woolley, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The small arm in the tray for the ice maker stopped moving. I put hot water in there to see if anything was clogging up the line or the tray, but nothing was. I then pushed on the arm and it moved pretty easily. So I took off the front cover and the motor; I saw that the plastic piece connecting to the gear was broken. So I realigned and replaced the motor. Ice maker is working like a champ again.

Icemaker stopped making ice.

  • Customer: Luz E from Crystal Lake, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video provided on your website and followed the directives. It was just as easy and simple as noted in the video.
All Instructions for the 10641522500
1,006-1,020 of 1,126