Models > 10641512100 > Instructions

10641512100 Kenmore Refrigerator - Instructions

All Instructions for the 10641512100
511 - 525 of 707
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken door
It is was easy to repair and just as easy to order from parts direct.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • samuel from layton, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
freezer was not consistent in keeping cold enough to keep itiems from defrosting. Fridge was not keeping up to temp. Noticed compressor would try to cycle but would cut out. Gave a Fonzerelli tap "ehhh" to the temp control and controls would kick on and work for short periods.
Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.
Parts Used:
Thermostat Assembly
  • Kurt from Staatsburg, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
compressor no run. smell of burning wires
I followed the inclosed (simple) instructions.
Parts Used:
Compressor Start Device Kit
  • NATHAN from MARIANNA, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Light switch inoperative
Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.
Parts Used:
Door Light Switch
  • Timothy L from Middlebourne, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken slide
simply slid the new part in place...really simple
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Evelyn from Indianapiolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Work sometime , sometime you have to tap around the thermostat area
Working from inside out . Remove left upper tube cover and then vent cover . Remove thermostat tube from around the vent . Remove knobs and front cover . Remove 4 hex screws , drop the whole unit enough to expose the left control rod , remove the rod retaining clip . Gently separate control rod from unit . Take the whole unit to working bench or table . Remove thermostat and bracket . Need to reuse bracket with new thermostat . Don't forget the clear plastic tube you have to reuse that as well . Be careful not to kink the thermostat tube . Reverse procedure , working from outside in . Good luck
Parts Used:
Thermostat Assembly
  • douglas from Alhambra, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The refrigerator would not cool
Only the compressor fan was running with no cold air, the compressor wouldn't kick on. I pulled the start relay and the disc inside was in pieces ( rattled when you shook it). I ordered the new one and installed it. The compressor started running right away and cold air was delivered to the freezer.
Parts Used:
Compressor Start Device Kit
  • justin from carlisle, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door would not close by itself
Followed instructions on this website. Only difference I placed a couple blocks under the door to keep it from dropping & removed both cams at the same time. No need to remove the door from the unit.
Parts Used:
Door Cam - Black Lower Door Closing Cam
  • rich from liberty twp, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
the refrigerator tunrs off and defrost
After watching the convenient movie, the replacment of the Thermostat was very simple and easy. i woul strongly advise you to take a picture of the wires before disconecting so, you will be sure to to reconetc it again.The replacment was a success and the refrigerator has been working since them
Parts Used:
Thermostat Assembly
  • dorival from pembroke pines, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Side Of Drawer Was Broken And Couldn't Run On The Guides.
Took the broken drawer out and installed the new drawer.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Valerie from Sevierville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old refrigerator drawer gave up the ghost--don't know why--plastic became brittle
Parts Select Website was very easy to use, selected the correct part for me with no problem. Same drawer as Sears was selling but for much less money. Drawer came in new from the factory. Great Service, Fast Delivery. The shipper had damaged the drawer--something poked through the box and put a whole in the drawer--a small one cause by a sharp instrument of some kind. Called parts select, the problem was very simply rectified by refunding my money and then I bought a new drawer at the same time. No fuss, no muss. Fast delivery and great service.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Lloyd from Spokane, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The slide/ glide portion of the original drawer broke off
Pretty simple, remove the old one and put in the new one - kinda alike the "Automotive Tech's" of today.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Doug from Acworth, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
old crisper drawer gave up the ghost--brittle
Nothing to it, just slide the drawer in. Fast Delivery, Smooth Transaction, Great Service. I will use them for all the parts I need in the future. Thanks
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Lloyd from Spokane, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
none
Took the old one out and put the new one in. No problem.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Nancy from Petersburg, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The door would not close tight unless you gave it an extra push
Removed the old cam and put books under the door to hold it up. Follows instructions and really easy
Parts Used:
Lower Door Closing Cam
  • Cindy from Kenner, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10641512100
511 - 525 of 707
Back to Top