10641269800 Kenmore Refrigerator - Instructions

internet search

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

I just want to share with everyone what a great experience this was. I called on a Monday night after the bottom shelf in our fridge broke and juice had just spilled everywhere. Needless to say I was annoyed so when I actually got in contact with a person instead of a machine I was excited. I did not get her name but she quickly helped me locate the model number, and even described the shelf to ensure it was the correct piece. She gave me the price, took my CC#, and within minutes the part was ordered. I could not believe that the part arrived the very next day - less than 24 hours. I was very impressed. THank you for making everything so easy. A new loyal customer!

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

This is a very easy fix. Begin by emptying the contents of the door. Then, just remove hinge cap and remove the three hinge screws. The door can then be lifted off the hinge pin and placed on its side. Once this is done, replace the two can pieces (one on the door and one on the frame). Then just lift the door back in place and secure the hinge. This job can be done by one person (maybe two if you need help place the door on a work surface) and will take just 15 minutes.

Took out the door bins, 1 bolt on the plastic cap, 3 bolts on the hinge, took the door off, replaced cam at the bottom, all same size bolts, reset the door spent longer time cleaning the door selfs all done by my self in less than 30 min. others said it helped to have second pair of hands "my wife would of just got in the way :)"

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Made the order which came in a timely fashion. But the new pan was cracked. I immediagely called. The agent was friendly, personable, and helpful. She ordered a new pan, but it didn't come as it was supposed too. Yesterday I went to the barn and , yep, it was there! Why fedx put it there I don't know. But it is in good shape. Only complaint it that I have to keep the other part for 30 days to wait for notification whether they want it back or not! Otherwise very glad to have this issue solved.

1. opened box with new drawer inside.2. washed new drawer. 3. opened fridge door 4. removed old defective drawer and threw it away. 5. Inserted new drawer 6. closed fridge door 7. opened fridge door to put veggies in new drawer. 8. closed fridge door when finished.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones