Models > 10641264801 > Instructions

10641264801 Kenmore Refrigerator - Instructions

All installation instructions for 10641264801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641264801
391-405 of 412
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drawer Damage (Cracked)

  • Customer: AKIHIRO from Maryville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just re-intall the new drawer. That's it. Thank you !!

Freezer OK. Refrigerator Not Cooling.

  • Customer: Donald from Kissimmee FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed recommendations from others but went with most likely by percentage = Defrost Timer Kit. Did not solve issue. Then went with Bi-Metal Thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part OK. Then I saw on line that I should have listened for Fan operation. I checked and found the fan Motor to be defective. Replaced the motor and Refrigerator worked fine. Both the Motor and Bi-Metal Thermostat were required. Should have checked fan operation first.

Broken roller wheels

  • Customer: Joseph from Tyrone PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

Refrigerator and freezer was not cooling. Lights inside refriogerator working . Compressor and fan was not on.

  • Customer: Cary from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug the refrigerator. With nut-driver and/or screw driver remove the lower back cardboard panel to access Start device. Use needle nose pliers to remove bracket holding Start Device along with capacitor. Disconnect the wiring connector from Start Device. Carefully, pry Start Device from compressor. Remove capacitor from Start Device. Replace the capacitor to the Start Device. Connect the Start Device with the capacitor to the compressor being mindful of the three male pins. Plug the electrical connector back into the Start Device. Finally, reconnect the bracket. . Reinstall the lower back cardboard panel. Plug in the appliance. Very simple and easy to install. Note: If the compressor and fan do not come on, reset the defrost switch which is located inside the refrigerator side underneath the right side of the refrigerator temperature selector with the flat head screw driver.

Cracked Crisper Drawer

  • Customer: Richard from Huntsville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the damaged unit and inserted the replacement.

Lower Door Closing Cams Worn down

  • Customer: Raul from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

fridge turned itself off, melting often

  • Customer: Irene from Margate FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I vacuumed the back and underneath, hoping it will solve the problem, but after about 2 weeks of hoping I succumbed.... finding the proper wrench was the most time consuming. After removing the screws, the face plate removal was the most challenging. You have to pry the top part carefully away (we used a knife), after it just drops down. Used a flat screw driver to loosen the wire harness, after that the rest was less than child's play. We are still in the testing mode, but so far so good. Freezer freezes, ice maker drops the ice cubes (not melting), fridge is humming. Wish us good luck.

Very Noisy

  • Customer: James from Fort Myers FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions provided on a video that was shown when I went to order the required parts. The video was very well done. It is very accurate.If you fololw the instructions you can make the repain in about 30 minutes. It was very easy

Refrigerator door was not closing "automatically", over time the plastic cams had worn out.

  • Customer: Mike from Egg Harbor Township NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

bottom door shelf bracket cracking

  • Customer: John from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unsnap old part and gently push new shelf bracket in till it snaps into place.

Refrigerator stopped cooling compressor did not cycle

  • Customer: james from indian springs AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug power! Remove the screws from lower panel on back of refrigerator. Lift wire mount out of back panel. Capacitor is mounted directly to the relay and overload switch located on the left side of the compressor. Remove the spring clip holding the capacitor in place and pull the old capacitor out. Plug in new capacitor and replace spring clip. Use vacuum to remove dust from drip pan and wipe fan blades clean. Replace wire into slot on back panel and replace screws. Remove front coil cover below freezer door. vacuum dust off coils and replace cover. Plug refrigerator in and enjoy cold beverages. Relay and overload kit were not required for this repair.

refrigerator and freezer would stay frozen.

  • Customer: Jack from Poplarville MS
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Broken Door Bin

  • Customer: Evelyn from Redwood City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy and amazed at how fast my order was processed. I received the parts next day. Wow!

broken crisper drawer

  • Customer: marie from metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The part fit perfectly. All I had to do was slide it in. Very speedy delivery and I am very satisfied with the service and would recommend your wedsite to anyone. Marie

Door would not close properly

  • Customer: George from Loudon TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions on line suggested I buy a lower door closing cam and a thimble top which I did. When I went to install I noticed that the door hinge with cam was also warn down. I had to again place an order and again remove the door to install. I would suggest those having this problem that they look at the hinge with cam also before ordering.
All Instructions for the 10641264801
391-405 of 412