Models > 10641263801 > Instructions

10641263801 Kenmore Refrigerator - Instructions

All installation instructions for 10641263801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641263801
301-315 of 433
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower door closing cam making loud snapping noise when opening or closing door

  • Customer: Robert from Punta Gorda FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed refrig. door and replaced closing cam and tightened the bottom cam

Crisper Drawer Plastic Drawer Guides Broken

  • Customer: David K from CHICAGO IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.

Didn't work once installed

  • Customer: BreathMinder from Merritt Island FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.

The drawer broke

  • Customer: robert from fox river grove IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I opened the box. That was the hardest part. I slid in the new drawer. I was a little distressed that my model # was not listed, but the pictures on your site were very helpful. Thanks

Refrigerator side was warm.

  • Customer: Robert from Olympia WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I was amazed how easy it was to replace this control board. I printed the pictures and instructions for the part that were on your site. There was a video for another part and it allowed me to get familiar with the layout of my unit. Thank you very much.

The door would not close completely

  • Customer: Roger from Punta Gorda FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

Fridge never had the ice-maker installed.

  • Customer: David from Salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

broken door shelf

  • Customer: Roberta from Springfield KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy in about 2 minutes. snap the old out and slap the new in

Very loud clicking noise when opening/closing door

  • Customer: Ben from Port Saint Lucie FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Replaced damaged pieces.

  • Customer: Thomas from Macomb MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered replacement parts from Parts Select on Sunday and the parts were delivered to my home on Wednesday . Could not be happier with this company. It was very easy to see exactly what I needed from the diagrams they provide on the website . Parts arrived and were installed in just a few minutes. I would, and have recommended Parts Select to my friends ... AWESOME !!

Small leak from icemaker

  • Customer: JOHN from VERO BEACH FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

Light switch which turns on the lights when the door opens went out

  • Customer: Dennis from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

door of the refrigerator would not pull itself closed.

  • Customer: Roy from Council Grove KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

Solid ice on Evaporator coil

  • Customer: PRAKASH from PISCATAWAY NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Dryer was constantly running and not getting hot

  • Customer: HENRY from WARMSPRINGS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.
All Instructions for the 10641263801
301-315 of 433