10641014100 Kenmore Refrigerator - Instructions

Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.

I followed the inclosed (simple) instructions.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Working from inside out . Remove left upper tube cover and then vent cover . Remove thermostat tube from around the vent . Remove knobs and front cover . Remove 4 hex screws , drop the whole unit enough to expose the left control rod , remove the rod retaining clip . Gently separate control rod from unit . Take the whole unit to working bench or table . Remove thermostat and bracket . Need to reuse bracket with new thermostat . Don't forget the clear plastic tube you have to reuse that as well . Be careful not to kink the thermostat tube . Reverse procedure , working from outside in . Good luck

Only the compressor fan was running with no cold air, the compressor wouldn't kick on. I pulled the start relay and the disc inside was in pieces ( rattled when you shook it). I ordered the new one and installed it. The compressor started running right away and cold air was delivered to the freezer.

Followed instructions on this website. Only difference I placed a couple blocks under the door to keep it from dropping & removed both cams at the same time. No need to remove the door from the unit.

After watching the convenient movie, the replacment of the Thermostat was very simple and easy. i woul strongly advise you to take a picture of the wires before disconecting so, you will be sure to to reconetc it again.The replacment was a success and the refrigerator has been working since them

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

I looked at the video that part select send. I did exactly what it said to do,and now my refrigerator is working just great. And the noise is gone. I thank you so much for your help. And I'm a 64 year old women thats how easy it was.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.