10640262010 Kenmore Refrigerator - Instructions

Push it in to place very easy.

Removed old crisper tray and inserted new crisper.jod done

I opened the refrigerator door, being careful to leave the freezer door closed. After verifying that refrigerator light was on, I squatted down to be at the same level as the crisper drawer. Firmly grasping the old crisper drawer by the convenient built-in handle, I pulled the drawer until it was fully opened. I removed the contents of the old crisper drawer, noting the original location of each item, so that I can place the contents into the replacement drawer in the same place. Grasping the old crisper drawer, I pulled outward and lifted slightly until the drawer was off the track and out of the refrigerator. Using both hands, I placed the rear of the new crisper drawer against the drawer track, lining the tabs on either side so that they would enter the track. I applied gentle, rearward pressure, guiding the new crisper door onto the track. This step was a little tricky. I had to wiggle the new crisper door up and down a bit, to get the new crisper door past the "stop bumps" in the track. After the new crisper door was sufficiently in the track to be supported by the track, I replaced the contents in (what I thought) the same locate from which they were removed from the old crisper drawer. After placing all contents back into the new crisper drawer, I applied a little more rearward pressure until the new crisper drawer was in the fully closed position. I then closed the refrigerator door. I quickly reopened the refrigerator door, to ensure the light went out. It was on. I slowly closed the refrigerator door, keeping an eye on the gap between the refrigerator door seal and the refrigerator cabinet, and noted the light did, in fact, go out when the door was about a half inch from being fully closed. Returning to a fully standing position, I announced to my wife that I repaired the broken crisper drawer. The congratulated me on my accomplishment and I felt a rush of satisfaction over a job well done.

Very easy to install. Followed instructions so took about 1 minute (including unpacking). Saved big money. Great company to deal with

Received new drawer in 2 days and effortlessly exchanged it for broken one. Color of writing didn't match but I just removed it from the old one and replaced it. Very pleased.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Simply slid the replacement into place. 30 seconds at most.

I just changed old drawer to new drawer

Removed mounting screws, disconnected control board( snap in connections), snapped in new connections installed 2 screws in new board and reinstalled the cover.

Removed old drawer, replaced with new one. Easy fix. New drawer fits perfect.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

Removed refrig. door and replaced closing cam and tightened the bottom cam

I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.