Models > 1058WH W > Instructions

1058WH-W Admiral Range - Instructions

All installation instructions for 1058WH-W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1058WH-W
16-30 of 109
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

electric coils would not stay flat as drip pans were incorrect fit

  • Customer: Janet from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
replaced drip pans with correct type

Drip bowls were burned and tacky

  • Customer: Donna from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
First I removed the old bowls and replaced them with the new.

burner would not work

  • Customer: David from Bellefonte PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you

Electric stove burners working intermitantly.

  • Customer: Michael from St. Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

Store-bought drip bowls wouldn't fit.

  • Customer: Sharon from Yacolt WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

burner inop

  • Customer: Donald from Milford MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

Door Spring Broke

  • Customer: Thomas from Van Nuys CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

FRONT BURNER WOULD NOT HEAT

  • Customer: GAIL from ORCHARD PARK NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
I CUT THE POWER TO THE CIRCUIT. REMOVED THE BURNER AND THEN UNSCREWED THE OLD ALUMINUM PLATE ATTACHED TO THE RANGE TOP COVER. OPENED THE TOPCOVER TO ACCESS THE WIRES. I CUT THE TWO WIRES BEING SURE THAT I LEFT ENOUGH LENGTH. I THEN SLIPPED THE TWO NEW WIRES WITH THE BRASS CONTACTS INTO THE NEW BLACK PLASTIC HOLDER UNTIL IT LOCKED. REATTACHED THE NEW METAL PLATE TO THE RANGE COVER, FED THE WIRES THROUGH AND SNAPPED THE NEW PLASTIC HOLDER INTO THE ALUMINUM PLATE. SECURED WIRE ENDS WITH THE CERAMIC WIRE NUTS. TOTAL TIME ABOUT 30 MINUTES.

Stove-top Burner intermittently shut off and on-wouldn't heat properly

  • Customer: George from New Bloomfield PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Burner would not heat up.

  • Customer: Nancy from Baldwinsville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

burner would not heat.

  • Customer: Jackie from Hughes Springs TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,

Couldn't find correct drip bowls that fit.

  • Customer: Lowell from Hardin KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.

The old drip bowls were rusting, no chrome left

  • Customer: kathryn from piqua OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Had 2 bad cooking elements and needed 4 new pans for the burners

  • Customer: Miles from Apache Junction AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordered the parts and when I received them I simply removed the old ones and replaced them with the new ones. No tools were required.
All Instructions for the 1058WH-W
16-30 of 109