Models > 1034347265 > Instructions

1034347265 Kenmore Dishwasher - Instructions

All installation instructions for 1034347265 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1034347265
1-12 of 12
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

There was no heat on the coils.

  • Customer: Shaohui from East Lansing MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 22 of 24 people found this instruction helpful
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.

Surface burner coil did not work.

  • Customer: Gregory from Mont Belvieu TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 14 of 17 people found this instruction helpful
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.

Have tried 3 different store-bought drip pan sets over the past year. None of them laid flat.

  • Customer: Jennifer from Saginaw MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
Simple installation of new pans and all are level! Thank heaven! Thank you, PartSelect!

Burners would not lay flat

  • Customer: Alfred from Forest VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

Finish coming off of bowls

  • Customer: Robert from Ledyard CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

Really, really grungy drip bowls

  • Customer: Donna from Brownfield TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Threw away old drip bowls, cleaned the top of the range, put on new bowls! So easy, a cave man could do it! All kidding aside, took knobs off and soaked them in hot soapy water for a while, cleaned part of stove behind knobs, cleaned under the burners, put it all back together, and while it doesn't look a new stove because it's at least 20 yrs old, looks 100% better. I think I can live with it for a while until I get brave enough to remodel my kitchen. Soooooo scary.....

Could not find the correct drip pan for my stove.

  • Customer: Kenneth from Oakford PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The drip bowls on my stove where getting rusty and I had a hard time getting the correct size for the 8 " burner. Wasted mony 3 times before finding it on partselect.

Finding a drip pan that fit so that pots could sit level.

  • Customer: Ann B from Hueytown AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.

Right Front [surface burner terminal block kit]

  • Customer: Wayne from Montoursville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.

Live in an apartment and they had generic drip pans on the stove causing pots to tilt when cooking.

  • Customer: Jennifer from Cleveland OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

Burner was unreliable...would stop working...I had already replaced the burner

  • Customer: Lelia from Vienna VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

the wires were not long enough to use the original path.

  • Customer: Ronald L. from Cedaredge CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.
All Instructions for the 1034347265
1-12 of 12