PartSelect Number PS2100114
Manufacturer Part Number 99002780
Sold individually.
|
Fixes these symptoms Not cleaning properly
|
Installation Instructions
Joseph from Merrill WI says,
Didn't spray water.
Inside the Dishwasher on the bottom of unit, I removed the dish cart. The removed the sprayer arm with an adjustable wrench on the plastic nut on the center top. Then removed the top three screws wit...
read more
|
PartSelect Number PS1602167
Manufacturer Part Number 33002970
|
Fixes these symptoms Takes too long to dry
|
Installation Instructions
Daniel from Millmont PA says,
Dryer wouldn't heat
This was the first time I ever attempted such a repair on an appliance, but it was fairly easy once I figured out how to take the front of the dryer off! I was almost certain that the igniter was the ...
read more
|
PartSelect Number PS2018556
Manufacturer Part Number 211124
This V-style pump belt is typically used with washing machines that use two belts. This belt is about 40.5" long and 3/8" wide. This pump belt helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.
Fixes these symptomsBurning smellLeaking waterPumps but will not spin
See more...
|
Installation Instructions
Charles from Whitman MA says,
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel. I pulled the washing machine away from the wall and ti...
read more
|
PartSelect Number PS344510
Manufacturer Part Number 3387134
Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.
Fixes these symptomsNo heat or not enough heatShuts off too soon on auto dryTakes too long to dry
See more...
|
Installation Instructions
John from Indianapolis IN says,
Dryer would take forever to dry clothes, even on high setting
I ordered all the thermal sensors for the dryer. They arrived two days later and they were the correct parts. It took me about 1/2 hour to replace all three sensors and now the dryer works like new ...
read more
|
PartSelect Number PS1964648
Manufacturer Part Number W10169313
This part replaces older two terminal switches.
|
Fixes these symptoms Will not shut offWill not start
|
Installation Instructions
Don from Jacksonville FL says,
Switch sticking in on position
FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two scre...
read more
|
PartSelect Number PS2351899
Manufacturer Part Number 6-2095720
This kit comes with hub assembly, seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
|
Fixes these symptoms Leaking water
|
Installation Instructions
douglas from bonita springs FL says,
water leaking from around center shaft below fixed tub
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water,...
read more
|
PartSelect Number PS2036214
Manufacturer Part Number 33002535
At 91-5/8" long, this dryer drum belt has 5 ridges and is 3/8" wide.
Fixes these symptomsUnusual NoiseWill not startWill not tumble
See more...
|
Installation Instructions
Mark from Lafayette LA says,
Dryer squeeking loudly becoming worse quickly
I received my parts promptly and had no problems, they were accurate and fit well.
After removing the screws to the front door and panel I removed the wires to the door switch. Carefully ...
read more
|
PartSelect Number PS344761
Manufacturer Part Number 338906
This part senses the flame for heat allowing the gas valve to open.
Fixes these symptomsNo heat or not enough heatShuts off too soon on auto dryTakes too long to dry
See more...
|
Installation Instructions
Michael from Kirkwood MO says,
Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer. 2. Removed two bolts at bottom front of machine and took...
read more
|
PartSelect Number PS600181
Manufacturer Part Number 312967
Fixes these symptomsNo heat or not enough heatTakes too long to dryUnusual Noise
See more...
|
Installation Instructions
Roberta from St. Louis MO says,
Dryer had been noisy, then stopped heating.
Opened dryer and removed drum. Replaced old blower wheel with new wheel, clamp and clipwhich was worn and was responsible for the noisy operation. Plugged in new ignition coils then replaced drum. ...
read more
|
PartSelect Number PS1570174
Manufacturer Part Number 12001656
This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.
Fixes these symptomsDoor will not open after self clean cycle endsLittle or no heat when bakingOven is too hot
See more...
|
Installation Instructions
David from Westford MA says,
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic con...
read more
|
PartSelect Number PS1583805
Manufacturer Part Number 205613
This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.
Fixes these symptomsLeaking waterNo hot or cold waterUnusual Noise
See more...
|
Installation Instructions
Brian from El Cajon CA says,
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place....
read more
|