Magic Chef Range Lights and Bulbs

Videos!

Your Price

$11.73

Magic Chef Range Light Bulb - 40W

★★★★★

66 Reviews

PartSelect Number PS884734

Manufacturer Part Number 8009

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-out bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.

Installation Instructions

judie from mays landing, NJ

interior drawers were off their rollers

pulled the washer out and replaces the top roller system on both sides and the replaced the weels and brackets on the bottom drwaer. however i had trouble putting the dish washer back correctly and had to call a repairman to adjust the dishwasher and alighn it to open and close properly. but i did do good inside. i feel it was easy and a success. thank you for having the supplies for us to attempt to repair it on our own. Read more...

Videos!

Your Price

$64.44

Magic Chef Range Light Cover Lens

★★★★★

7 Reviews

PartSelect Number PS11747414

Manufacturer Part Number WP9781049

The light cover lens in your oven is designed to protect the light bulb. If your light cover lens is damaged, you will need to replace it. This part is made of clear glass and is roughly 3 inches in diameter. Many of our customers have rated this repair as easy, and it should take less than 10 minutes to complete. In order to do this repair, simply unscrew the old light cover lens, and replace it with the new one. If your old light cover lens is damaged, be careful of any broken glass when completing this repair.

Installation Instructions

Jim from Placentia, CA

Oven (not broiler) element burned out, no oven heat

Inside the oven, I removed one Phillips screw on each side where the element mounts to the back oven wall. Then disconnected the wire on each side using pliers. Unscrewed glass lens, unscrewed light bulb. Replaced all pieces in reverse order. Took less than 10 minutes. Read more...

Your Price

$11.10

Magic Chef Range Indicator Light

★★★★★

3 Reviews

PartSelect Number PS11744053

Manufacturer Part Number WP74004153

Installation Instructions

Zaven from Fairfax Station, VA

No clock, and No oven control

Checked power. Had power to the oven, but no response from the control panel (Clock). Noticed that lower oven light was intrmittent.
Ordered parts.
When parts arrived, removed power, Removed front panel (three screws). Replaced old control panel and lower oven indicator light, Replaced panel. Turned power back on,
AND IT WORKS. Read more...

Videos!

Your Price

$6.05

Magic Chef Range Indicator Light Lens

PartSelect Number PS11740971

Manufacturer Part Number WP3196068

Installation Instructions

John from Somersworth, NH

Switch burnt out/Lens broken

Removed the three screws holding on the back plate and removed plate.

Popped out the switch and used the pliers to pull off the wires. Connected the wires to the new switch.

Popped out the broken light. Slid the new lens into the front panel. Slid the light housing onto the new lens.

Re-attached the back plate. Read more...

Your Price

$50.93

Magic Chef Range Light, Indicator (Surface Unit

PartSelect Number PS11746053

Manufacturer Part Number WP8523265

Your Price

$53.91

Magic Chef Range Light Bulb - 120v 25w

★★★★★

3 Reviews

PartSelect Number PS11747808

Manufacturer Part Number WPA3167501

This is a 120 volt, 25-watt light bulb that fits a variety of medium to large kitchen appliances. It functions by illuminating when the appliance door is open. It has a small base with a twist lock. This part is sold individually. This is a common wear part, so it is recommended order a spare and to check other appliance light bulbs in your home. This is an authentic OEM part that is sourced directly from the genuine manufacturer. Be careful when handling the light bulb; use a pair of needle nose pliers to remove the base if the glass bulb is broken.

Installation Instructions

Thomas from Oneonta, NY

Dryer made a loud noise and vibrated badly

First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created. Read more...

Your Price

$99.73

Magic Chef Range Light Blub - Fluorescent - 18 Watt

PartSelect Number PS11746888

Manufacturer Part Number WP95292

This light bulb is used in a range's control panel.

Installation Instructions

Jeffrey from Marietta, GA

Light Bulb burned out

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys. Read more...