Quick Question!

Have you ever purchased from PartSelect.com before?

Popular Magic Chef Dryer Parts

Your Price
$14.56
Multi Rib Belt - 92-1/4"
PartSelect Number PS346995
Manufacturer Part Number 341241
This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.
Fixes these symptoms
Heat stays on after drum has stopped
No heat or not enough heat
Noisy

See more...
Installation Instructions
Ray from Denton, TX says,

Dryer tub belt broke
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of ...read more

Your Price
$21.73
'M' Series New Style Coil Kit
PartSelect Number PS334310
Manufacturer Part Number 279834
This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.
Fixes these symptoms
No heat or not enough heat
Noisy
Shuts off too soon

See more...
Installation Instructions
Michael from Kirkwood, MO says,

Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.
2. Removed two bolts at bottom front of machine and took...read more

Your Price
$14.78
Door Catch Kit
PartSelect Number PS2162263
Manufacturer Part Number LA-1003
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appliance to both start and complete a full drying cycle. There are two pieces included in this kit, one catch, and one strike. You open and close the door on such a regular basis that this mechanism can wear out. It is a fairly common part to replace. You will need to remove the door of your dryer to install the replacement catch assembly.
Fixes these symptoms
Door won’t close
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
Paul from Mt. Pleasant, SC says,

catch mounted on door broke
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was...read more

Your Price
$15.68
High Limit Kit
PartSelect Number PS2162282
Manufacturer Part Number LA-1053
The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit thermostat with a limit at 300. The thermal fuse kit shuts off the motor in the dryer when it begins to overheat. If the dryer will not heat, is overheated, shuts off too soon, or takes too long to dry then the thermal fuse might have exploded and need to be replaced. For replacement instructions refer to the diagram by manufacturer. For safety, unplug the dryer before installing the part.
Fixes these symptoms
No heat or not enough heat
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
Ronald from Fredericksburg, VA says,

Electric dryer would not heat - Thermal fuses - $25 fix - I love DIY
1. Unplug dryer from power outlet
2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift.
3. Locate heating element ...read more

Your Price
$13.31
Lint Filter
PartSelect Number PS11742807
Manufacturer Part Number WP53-0918
This is an OEM lint filter for a dryer. This lint filter screen has two side guides on either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide. This part is white and is made of plastic. You may need to replace the filter if the plastic is broken or warped. Simply slide the lint filter out of the slot and slide the replacement filter in. The lint filter collects lint from drying clothes and prevents lint from building up in internal moving parts, specifically the heating coil. Neglecting to clean your lint filter is a fire hazard, be sure to clean it on a regular basis.
Fixes these symptoms
No heat or not enough heat
Noisy
Takes too long to dry

See more...
Installation Instructions
Jane from Grand Forks, ND says,

lint filter broke
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wedn...read more

Your Price
$27.70
Radiant Flame Sensor
PartSelect Number PS11741429
Manufacturer Part Number WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.
Fixes these symptoms
No heat or not enough heat
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
Michael from Kirkwood, MO says,

Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.
2. Removed two bolts at bottom front of machine and took...read more

Your Price
$43.29
Heating Element Kit - 240V 4750W
PartSelect Number PS2162280
Manufacturer Part Number LA-1044
This dryer heating element kit is 240 volts and 4750 watts. The kit comes with a high limit thermostat of L248-80. The function of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your clothes take too long to dry, or if your dryer is not getting any heat or enough heat, you may need to replace your element. Before you begin your repair, make sure to disconnect the power from the dryer. The tools you will need for this repair include a putty knife, a quarter-inch nut driver, and a pair of needle nose pliers.
Fixes these symptoms
No heat or not enough heat
Takes too long to dry
Too hot

See more...
Installation Instructions
Brianna from Littleton, CO says,

Dry stopped heating - still had good air flow
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a ...read more

Your Price
$50.03
Rear Drum Support Roller Kit
PartSelect Number PS2162268
Manufacturer Part Number LA-1008
The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.
Fixes these symptoms
Noisy
Will not tumble


Installation Instructions
Michelle from Kirkwood, MO says,

Dryer squeaking really badly
I opened the dryer from the front by pushing in on the two clips just under the top. I then had to remove two screws on each side and took the front panel off. I reached around underneath on the rig...read more

Your Price
$8.98
Thermal Fuse
PartSelect Number PS11741460
Manufacturer Part Number WP3392519
This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. This replacement part features two 3/16 inch terminals, and is sold individually. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.
Fixes these symptoms
No heat or not enough heat
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
ANTHONY from CHESHIRE, CT says,

Dryer was working, but no heat.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and...read more

Your Price
$14.96
Thermostat, Internal-Bias
PartSelect Number PS11741405
Manufacturer Part Number WP3387134
A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees and will then turn off and then on again once it has dropped by 25 degrees. If your dryer is not giving off enough heat, is over-heating, is not turning on, or is having issues with the timer functionality, this could indicate an issue with the thermostat. The installation of the cycling thermostat is simple and the only tool required is a 1/4 inch nut driver (and gloves for safety).
Fixes these symptoms
No heat or not enough heat
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
Tom from High Point, NC says,

Dryer blew cold air.
PartSelect is great for providing parts as requested. Unfortunately, neither of the 2 parts I ordered were on my machine. My bad for not looking at the actual part instead of the description. A word t...read more