Kenmore Washer Filters

Your Price

$26.76

Kenmore Washer Pump Filter

★★★★★

10 Reviews

PartSelect Number PS3522306

Manufacturer Part Number 383EER2001A

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Sandra from Livonia, MI

The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.

Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again! Read more...

Your Price

$13.61

Kenmore Washer Screen

★★★★★

1 Review

PartSelect Number PS11746894

Manufacturer Part Number WP96160

Found on the water inlet valve.

Installation Instructions

Peter from Aurora, IL

The fill cycles would start then stop suddenly

This was an easy repair.
1st I removed both water hoses
2nd I removed 1 hex head screw that released a backing plate & removed the plate holding the water inlet valve.
3rd I pulled the 4 electrical connections & loosened a clamp to remove a small water hose.
4th I removed 2 hex head screws that held the water valve to the backing plate.
-----------that was a whole 5 - 10 minutes!------------
Next I reversed the process
4th I attached the inlet valve with the 2 hex head screws
5th re-attached the 4 electrical connections(had slip on spades) pushed on the hose & tighterned the clamp.
6th replaced the backing plate with the inlet valve attached & tightened the single hex head screw.
7th re-attached the hot & cold lines................................DONE
15 minutes tops Read more...

Your Price

$22.90

Kenmore Washer Inner Tub Filter Plug Kit

PartSelect Number PS334684

Manufacturer Part Number 285868

Kit contains 4 plugs - replaces the lint filter that goes under spin basket. The filter under the spin basket is no longer required. Replaces round filter assembly.

Fixes these symptoms

Marks left on clothes
See more...

Installation Instructions

Bob from East Palestine, OH

The motor turned with loud noise ,but nothing else worked

I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again. Read more...

Your Price

$16.48

Kenmore Washer Water Inlet Valve Filter Screens

★★★★★

2 Reviews

PartSelect Number PS3618281

Manufacturer Part Number AGM73269501

This includes one orange screen and one blue screen.

Installation Instructions

Keith from ROCKAWAY, NJ

Water was leaking into washing machine after the washer was shut off

Removed the cover from the washing machine, the two valves(cold & hot) are located in the read top of the machine, removed the hoses to the valves, removed the nut that holds on the valve to the washer and placed new valve into washer and placed the nut back onto new valve, placed the hoses back onto the new valve. Read more...

Your Price

$43.37

Kenmore Washer Lint Filter

★★★★★

1 Review

PartSelect Number PS11750500

Manufacturer Part Number WPW10215093

Your Price

$73.65

Kenmore Washer Noise Filter Assembly

★★★★★

2 Reviews

PartSelect Number PS3528920

Manufacturer Part Number 6201EC1006T

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

JOHN from FORT MYERS, FL

No power to dishwasher. Confirmed that outlet had power coming out.

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day. Read more...