Jenn-Air Microwave Latches

Your Price

$8.19

Jenn-Air Microwave Locker

★★★★★

15 Reviews

PartSelect Number PS3522838

Manufacturer Part Number 4026W2A019A

The locker, or door latch assembly fits to the inside of the microwave door, and keeps the door closed. If the door on your microwave oven doesn’t appear to close properly, you may have a problem with the door latch assembly. This locker is made of plastic and measures 7 inches long x 2 inches wide. If either of the hooks is broken or does not have any spring tension, you may need to replace the assembly.

Fixes these symptoms

Door not closing properly
See more...

Installation Instructions

Christine from LUXEMBURG, WI

The over the stove microwave door would not close.

I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience. Read more...

Your Price

$10.45

Jenn-Air Microwave Interlock Support

★★★★★

4 Reviews

PartSelect Number PS11749178

Manufacturer Part Number WPW10156813

Also known as a switch holder.

Fixes these symptoms

Door not closing properly
Won’t turn on
See more...

Installation Instructions

Mark from HOMER GLEN, IL

Door switch inconsistent operation for Open/Close sensing.

Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 Phillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time. Read more...

Your Price

$23.82

Jenn-Air Microwave Top Interlock Support

★★★★★

5 Reviews

PartSelect Number PS11745301

Manufacturer Part Number WP8206419

Fixes these symptoms

Door not closing properly
Won’t turn on
See more...

Installation Instructions

Mark from HOMER GLEN, IL

Door switch inconsistent operation for Open/Close sensing.

Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 Phillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time. Read more...

Your Price

$18.88

Jenn-Air Microwave CAM-PLATE

PartSelect Number PS9491943

Manufacturer Part Number W10562613

Fixes these symptoms

Door not closing properly
Won’t turn on
See more...

Installation Instructions

Mark from HOMER GLEN, IL

Door switch inconsistent operation for Open/Close sensing.

Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 Phillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time. Read more...