Husqvarna Tiller Parts

Your Price

$3.99

Husqvarna Tiller Clevis Pin

★★★★★

2 Reviews

PartSelect Number PS9009427

Manufacturer Part Number 532132673

This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long and made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.

Ring Klip Number T5304-75 – Part Number: 812000029

Your Price

$3.99

Husqvarna Tiller Ring Klip Number T5304-75

★★★★★

1 Review

PartSelect Number PS9143890

Manufacturer Part Number 812000029

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

Installation Instructions

Anthony from OLIVEHILL, TN

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...

Your Price

$12.44

Husqvarna Tiller Chute

★★★★★

1 Review

PartSelect Number PS11824789

Manufacturer Part Number 585056901

This chute base, also known as a discharge chute base, is sourced from the original manufacturer for use with snowblowers. It is found at the end of the discharge chute which is responsible for directing the discharge of snow, or other materials that are being thrown by the equipment. The chute base is found at the end of the discharge chute where it acts as a connection point between the chute and the auger housing. The chute base aids in directing the discharge to a specific place, as well as controlling how far the discharge is thrown. If the chute base becomes damaged, cracked, or worn out, it will need to be replaced. A faulty chute base will result in snow being thrown haphazardly, not being thrown far enough or not thrown at all. It can also create blockages in the equipment, leading to potentially expensive repairs. Remove the fasteners that secure the base to the equipment and pull off the old chute base. Align the new chute with the mounting backet and secure it with the fasteners.

Your Price

$3.99

Husqvarna Tiller Clip, Hairpin

PartSelect Number PS9007536

Manufacturer Part Number 532003146

This hairpin clip, also known as a cotter pin, is a genuine OEM sourced part used to secure rotating components together in various outdoor power equipment. It is made of steel and is approximately 1.5 inches long. The clip acts as a fastener to prevent the moving parts from loosening and falling off during usage. The clip is vulnerable to corrosion and general wear over time. However, it can also fail prematurely due to overloading and excessive stress. A damaged hairpin clip will result in misalignment of parts, accidental disassembly, increased friction and wear, and potential harm to the user. Remove the faulty pin and align the new one with the insertion points. Ensure that the pin is securely fitted in its appropriate slot and compress the ends to prevent it from dislodging.

Your Price

$3.99

Husqvarna Tiller Handle Knob

PartSelect Number PS9020379

Manufacturer Part Number 532185577

Nut, Hex, Flangelock – Part Number: 532409149

Your Price

$4.99

Husqvarna Tiller Nut, Hex, Flangelock

PartSelect Number PS9022497

Manufacturer Part Number 532409149

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To replace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.