Frigidaire Cooktop Switches

Your Price

$40.14

Frigidaire Cooktop Burner Switch Kit

★★★★★

8 Reviews

PartSelect Number PS470145

Manufacturer Part Number 5303935086

This is a burner switch kit, also known as the surface element control switch repair kit, for ranges. This burner switch kit sends voltage to the surface element coil and it controls the stove top surface burner. If the following symptoms occur, installing the switch could be the solution to the problem: surface element not heating, overheating, or inconsistent heating. Usually, if the element is not defective, that is a sign there is an issue with the switch. The kit comes with several insert sizes, and includes screws as well. The tools needed for this project are a nut driver, pliers, and screwdrivers.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

George from New Port Richey, FL

High heat reluctant to turn down.

Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match. Read more...

Your Price

$68.44

Frigidaire Cooktop Surface Burner Switch

★★★★★

6 Reviews

PartSelect Number PS2342883

Manufacturer Part Number 318293827

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Gary from Herrick, IL

Burner would consistantly go to high no matter where the dial was positioned.

First I unplugged the stove.Removed the upper control panel back (10 phillips screws). Removed the plastic dial( pulls straight off). Removed the 2 screws behind the dial that is holding the switch in the control panel. Took one wire at a time off the old switch and put them on the new switch according to each electrical spade marking. L1, L2, H1, H2 and P. Installed the new switch in the control panel securing it with the 2 screws. Installed the dial, installed the upper back panel using the old screws. Plugged the stove back in and tested it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it. Read more...

Your Price

$71.82

Frigidaire Cooktop Surface Burner Switch - 8 Inch

★★★★★

1 Review

PartSelect Number PS2342881

Manufacturer Part Number 318293825

This switch controls the large surface burner. As per manufacture the original screws will damage new switch. New screws are needed.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Leon from Deer Paerk, TX

switch was not turning off had to jiggle it to go off

no problem slightly different shape than original but labels for wires matched up mounting screws aligned perfectly works great Read more...

Your Price

$132.24

Frigidaire Cooktop Dual Infinite Switch Kit

PartSelect Number PS981086

Manufacturer Part Number 903057-9010

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
See more...

Your Price

$71.41

Frigidaire Cooktop Burner Infinite Switch - 240V

PartSelect Number PS1529263

Manufacturer Part Number 318293818

Your Price

$65.09

Frigidaire Cooktop Surface Element Switch

PartSelect Number PS2342877

Manufacturer Part Number 318293814

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Fred from Redmond, OR

Burner would stay on high heat only. Repairman wanted $278.00 to fix...I bought the switch for under $30.00 delivered and spent 10 minutes fixing it myself.

Turned power off to the stove at breaker box. Pulled the 4 plastic knobs off of the stove. Unscrewed the 4 round parts that are directly under each knob to gain access to the switches. Took the two small phillips screws out holding the bad switch. Installed the wires from the bad switch to the new switch and then reinstalled everything in reverse order. I saved over $200.00 by doing this repair myself with only two screwdrivers. Read more...

Your Price

$71.87

Frigidaire Cooktop Surface Burner Switch - 6 Inch

★★★★★

1 Review

PartSelect Number PS2342880

Manufacturer Part Number 318293824

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

KEVIN from CADET, MO

burner wouldnt heat

took out 2 screws and disconnected wires . Read more...

Your Price

$106.22

Frigidaire Cooktop Spark Module - 120V

PartSelect Number PS468140

Manufacturer Part Number 5303912606

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Jonathan from Arkport, NY

My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.

First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove. Read more...

Your Price

$144.64

Frigidaire Cooktop Surface Burner Switch

★★★★★

1 Review

PartSelect Number PS443494

Manufacturer Part Number 318120505

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

scot from keller, TX

Burner eye would only produce High Heat on all settings

Ordered a new Surface Burner Switch to replace the failed unit.
When I opened the burner lid, I could see the insulation on all the wiring for the burners had fallen apart and wiring was exposed. The wiring for all 4 burners was exposed as the insulation had deteriorated and fallen off over 80% of the circuits. It was just blind luck there was not a fire or an electrical failure on a grand scale. I replaced the wiring and burner connection assemblies as they also showed signs of age and deterioration.
Had the switch not gone bad, forcing me to look into the wiring assemble, there very likely would have been an electrical fire. In a 220 volt appliance, electrical fires are a lot more excitement than I need.

Scot Hooper
Keller Texas Read more...