Quick Question!

Have you ever purchased from PartSelect.com before?

Popular Electrolux Cooktop Parts

Your Price
$32.76
Temperature Sensor
PartSelect Number PS820208
Manufacturer Part Number 316217002
The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.
Fixes these symptoms
Element will not heat
Little to no heat when baking
Oven is too hot

See more...
Installation Instructions
Dan from Bellevue, ID says,

Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug...read more

Your Price
$3.52
Main Terminal Block Kit
PartSelect Number PS471605
Manufacturer Part Number 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
Fixes these symptoms
Element will not heat
Little to no heat when baking
Oven not heating evenly

See more...
Installation Instructions
Timothy from Spring Valley, AL says,

Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washe...read more

Your Price
$120.02
Inner Oven Door Glass
PartSelect Number PS439086
Manufacturer Part Number 316117500
This inner oven door glass, also called an oven heat barrier glass, is a transparent and heat resistant sheet of glass that fits into your oven or range. While containing the heat, the sheet of glass acts like a window so you can see the contents in the oven. This is an original part sourced directly from the genuine manufacturer. Wait to replace the glass until the appliance is cool to the touch. This part is sold individually, and contains the glass panel only. Glass panel is approximately 20 inches by 13 inches.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Mitch from Fernandina Beach, FL says,

Cracked oven door inner glass
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after r...read more

Your Price
$14.19
Surface Element - 8" - 2600W
PartSelect Number PS2339242
Manufacturer Part Number 316442301
The range surface element provides heat to the cooking surface on top of the range. The element has a universal plug, is 8 inches in diameter, spans 5 coils in width and reaches 2600 watts. Before you begin your repair, ensure that the elements are turned off and have had time to cool. Once you have removed the element this is a good time to ensure the terminal is in good condition (they can wear over time) which may need to be replaced as well. This quick repair requires no tools except gloves for safety, and a small amount of time.
Fixes these symptoms
Element will not heat
Will Not Start


Installation Instructions
David from Encinitas, CA says,

burner shorted out
I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner....read more

Your Price
$90.26
6" Radiant Element with Limiter - 1200W
PartSelect Number PS1528719
Manufacturer Part Number 318178110
This is a six-inch radiant element with limiter. It works in conjunction with your stove top range. The purpose of this part is to heat up the cooking area that is located on top of the range, also known as your stove top. If you suspect that your surface element is not properly heating then you may want to test the element for continuity. This model is sold individually and is 1200 watts. The tools you will need for this installation include a Phillips screwdriver and a 14-inch nut driver.
Fixes these symptoms
Element will not heat


Your Price
$22.96
Light Bulb Lens
PartSelect Number PS2349721
Manufacturer Part Number 318406100
The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Jim from Harrison, MI says,

Lower baking element would not heat up.
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I...read more

Your Price
$43.77
Outer Drawer Glide
PartSelect Number PS977459
Manufacturer Part Number 316105501
As per the factory, the original part was 19 3/4 inches and the new substituted part is 16 1/4 inches. According to the factory, this part will still work with your appliance.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
james from evansville, IN says,

glide bearings came apart due to wife overloading drawer
removed 1 screw from each glide, pulled parts out, replaced parts and screws, slid drawer glides into bearing glides. job done, very easy and fixed problem....read more

Your Price
$212.54
Flat Glow Bar Igniter
PartSelect Number PS444179
Manufacturer Part Number 318177710
This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you may need to replace this part. The flat glow bar igniter is in the back of your gas oven. You will need to remove the access panel on the back of your oven to disconnect the igniter. Be sure that the gas source to the oven is shut off before you begin this repair. This part is sold individually.
Fixes these symptoms
Gas igniter glows, but will not light


Your Price
$11.59
FAN BLADE
PartSelect Number PS3409337
Manufacturer Part Number 318398302
Fixes these symptoms
No Symptoms for this part
Installation Instructions
John from Stevensville, MD says,

replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a cou...read more

Your Price
$11.42
Surface Element - 6"
PartSelect Number PS2339239
Manufacturer Part Number 316439801
This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits most electric ranges. All burners are made of a heating wire that produces heat from electricity. Remove the non-functional burner element from the terminal block (or receptacle). Use a multi-meter to check for continuity. Check the end of the terminals for corrosion or heat damage. If there is corrosion or heat damage, replace the whole terminal block or receptacle at the same time you replace the damaged coil. Before you start this repair, make sure that the element is turned off and cool to the touch.
Fixes these symptoms
Element will not heat


Installation Instructions
Steve from North Troy, VT says,

replaced elements
pull the element out and slide the new element in.No tools needed,it's that easy....read more